Electric motor make, lamco, model no.EC34-1(93) reversing 120v 16.5amps
I need info on how to re-wire this electric motor to a manual rotary switch. not for a tv not for a car but a electric motor. moteur electric. I have colour codes connected to a board, connections w1, w2, v1, v2, u1, u2. lamco electric motor model no#C34-1(93) reversing electric motor 120v, 16.5amp. this is not a cat, a tv or a car but a electric motor
You have to test the windings with multimeter to identify start winding, vrs run winding. Both windings receive power at same time. The start winding is like first gear on a car. It starts the motor rotation. The run winding brings motor up to rated speed.
Sometimes categories at Fixya are muddied, and people do not say which product they have, or give UL number instead of product number, and sometimes fixya questions are truncated onscreen ... so person answering question thinks the product is a gasoline powered bobcat, instead of hybrid car, or 120Volt single-phase electric motor.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The BOX is a GE splicer - with 6 wires - 2 grey power wires, then the red, blue, black, and white from the fan motor. I have the same problem and cannot find another GE SPLICER 3 SPEED SWITCH for the fan. All switches that I have tried have 4 connections.........so a WIRING DIAGRAM would be GREAT!
Can anyone offer any help? I have tried every electrical store in the area!
I ran into this when replacing the 3 spd switch. The replacement switch has a pair of connections at each position; you would assume the two connections are electrically tied together, they are not. The switch assembly actually has two seperate 4-position rotary switches. If your "L" wire is on the 'inner' connection, then your motor speed wires will have to be as well.
Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
Damaged turn signal and windshield wiper switch .
Damaged windshield wiper motor .
Damaged windshield wiper control module.
Wiper Motor Ground (Park)
Wiper Module to Wiper Motor (Park Switch)
Wiper Motor Power (Park Feed)
Wiper Motor Common (RUN)
Wiper Motor LO
Wiper Motor HI
Windshield Wiper System
The windshield wiper system consists of :
Windshield wiper motor (17508) (F-type).
Windshield wiper control module.
Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
Located at the instrument panel fuse panel.
The windshield wiper motor is:
Attached to the cowl top extension (021A36) .
Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
Rotary wiper switch.
Push type washer actuator.
Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
The windshield wiper motor has a brush rigging that permits selection of low or high speed.
When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
When the park switch contacts open, the windshield wiper motor stops in the park position.
When the turn signal and windshield wiper switch is in the interval position:
The wipers make single wipes separated by pauses.
The rotary switch is on the end of turn signal and windshield wiper switch .
The length of the pause can be set from approximately 1 to 17 seconds.
Length of pause decreases as the rotary switch is rotated away from off.
Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
It is normal to hear a slight click at the beginning of each on/pause cycle.
NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.