Question about Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

Zanussi DE 6965

What does AL6 fault mean on the display panel and how do we fix it

Posted by Tony Love on

  • Anonymous Sep 07, 2008

    the pump is emptying the dishwasher but not allowing it to go any further it just goes straight to alarm 6

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Hello Russel A L 6 Is Water Drain Time-Out Possible causes are; a) Domestic drain outlet unsuitable (obstructed) b) Motor faulty (pumps group/ drain impeller) c) Pressure switch faulty d) IWMS- Pressure switch tube obstructed e) IWMS- Sump vent hose obstructed f) Control board (Relay interrupt Regards David Marsh

Posted on Jul 18, 2007

  • Anonymous Jul 18, 2007

    TIME-OUT WATER DRAIN ALARM [A L 6]
    This control procedure is operative in all the drain phases and checks the status of the pressure switch in order to ensure that the cycle is performed correctly.
    􀂪 In all the final drain phases, and before passing to the subsequent phase, the pressure switch contact must be open on "empty". (1-2).
    􀂪 If the contact is closed on "full" (1-3), the drain phase is repeated
    􀂪 At the end of the second drain phase, if the pressure switch contact remains closed on "full" (1-3), an alarm condition is generated.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E60 fault, zanussi 1400 progress


Call someone to fix the problem

Jan 06, 2015 | Zanussi Washing Machines

1 Answer

My frost free fridge freezer is working but flashing de on the front. I'd like to know what it means


Error codes are brand (and often model) specific. "de" likely indicates something in the defrost process, especially on G.E. Check for ice build-up in the freezer cooling coil. The control board would be suspect, but must be checked to confirm the precise fault.

Oct 20, 2014 | Refrigerators

1 Answer

Zanussi double oven switches off during cooking. It can be restarted without a problem so fault can not be detected. It displayed error 3 message once.


The shutting down of the oven is due to a defective thermal switch or thermistor. Replacing the thermistor could fix the problem. It is usually located in the inside compartment of the oven and connected to the control panel board.

Dec 02, 2010 | Zanussi Ovens

2 Answers

My Zanussi zwf1650w comes up with a message draining 0 0 after about 30 seconds of starting a wash cycle. The machine the stops and bleeps saying cycle ended, is there a solution to fix this?


zanussi zwf1650w washing machine. when starting any program after a few seconds machines stops and shows draining 0.0. have done diagnosis test and shows fault E91 & E48 fault codes also shows E34 code. any help much appreciated.

Nov 05, 2010 | Zanussi ZWF1650W Front Load Washer

1 Answer

Hi could you tell me what AL6 means on my dishwasher and how to fix the problem, thanks


it may be the WMS is blocked, i get AL5 or AL6 at the start of the program. here is how i have fixed it the last couple of times. WMS is around £70 (in 2010) - i have that on mine every 4yrs or son - i change the WMS sometimes called the water management system or water softener. it located on the left of the machine. the floor will get wet during this repair.
you need to turn off the power; turn off the water supply; to it take the top off remove the two screws at the back of the lid. then work your way around the left hand side removing the panel retaining screws. once that is off you can see a large blue plastic 'thing' this is the WMS that you need to replace. to remove this you need to remove the screws around the inlet for the water, i think there are 5 or 6, some are revealed once cover plates are removed. there are 5 or 6 retaining the WMS; the most important are the tow at the bottom toward the middle. now gently prise off the WMS releasing the tabs and catches. do not pull it off as there are some connections still to be disconnected. As to lift the WSM at the bottom right, behind the WMS there are three pipes held on with spring clips, these need to be released. then the WMS should lift off.. replacing is the reverse of the above. i did not find it too difficult other than the last bit with the pipes but you know your abilities. Good Luck

Jun 08, 2010 | Zanussi 24 in. DE6965 Built-in Dishwasher

2 Answers

The Zanussi Aquapulse (de 6965) Fault Code AL3.


i have this now- another site suggested its the heater, or rater the circuit board. I have just taken it apart and have two dry solder points that are identified quire easily by soot around the area. so now off to find my soldering iron!!

Sep 26, 2009 | Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

Zanussi aqua pulse 6965 AL5 error


it may be the WMS is blocked, i get AL5 or AL6 at the start of the program. here is how i have fixed it the last couple of times. WMS is around £70 (in 2010) - i have that on mine every 4yrs or son - i change the WMS sometimes called the water management system or water softener. it located on the left of the machine.
the floor will get wet during this repair.
you need to turn off the power; turn off the water supply; to it take the top off remove the two screws at the back of the lid. then work your way around the left hand side removing the panel retaining screws. once that is off you can see a large blue plastic 'thing' this is the WMS that you need to replace.
to remove this you need to remove the screws around the inlet for the water, i think there are 5 or 6, some are revealed once cover plates are removed.
there are 5 or 6 retaining the WMS; the most important are the tow at the bottom toward the middle.
now gently prise off the WMS releasing the tabs and catches. do not pull it off as there are some connections still to be disconnected. As to lift the WSM at the bottom right, behind the WMS there are three pipes held on with spring clips, these need to be released. then the WMS should lift off.. replacing is the reverse of the above.

Jul 13, 2009 | Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

Error 10 message


Hi

E10 means there is no water getting in to machine.
check water supply if ok then fault will be fill valve.

regards

Mar 07, 2009 | Zanussi ZWF1430W Front Load Washer

Not finding what you are looking for?
Zanussi 24 in. DE6965 Built-in Dishwasher Logo

Related Topics:

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Paul Carew

Level 3 Expert

3534 Answers

Renee Knafel-Bullock
Renee Knafel-Bullock

Level 2 Expert

357 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...