Question about Apple Cinema HD 23" LCD Monitor

No picture began with the problem of difficulty in turning the power on with finger to the power switch senser(finer need to stay there continuesly for a while with white light on and off), finally the white will not come on at all. The power supply is normal giving out 24.5 V. Anyway to open up the monitor?

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.
Master
2,985 Answers

Is there a Mac technical help site or a mac user forum ? these are bit specialist for us PC'rs

Posted on Jun 03, 2007

1 Suggested Answer

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Need Some Help, My Psp 3001, Turns Off On It's Own, While I'm Playing A Game Or Listning To Music, What can i do???

Here are some instruction to help fix your problem.
Put the PSP down on a table with the LCD screen facing up.

2 Plug the power cord of the PSP power supply into the PSP's power outlet. Plug the AC plug of the PSP power supply into an AC socket.

3 Perform a hard reset on the PSP by pushing up on the power switch at the lower-right corner with your index finger.

4 Count to 15. Release the PSP's power switch. Count to 30.

5 Flick the PSP's power switch up with your index finger and release it. Repeat this procedure a second time.

6 Wait as the PSP reboots, starts up and stays on.

7 Remove the PSP power supply's power cord from the PSP's power outlet. Remove the PSP power supply's AC plug from the AC socket.

8 Flick the power switch up with your index finger to turn off the PSP.

May 04, 2011 | Video Game Consoles & Games

2 Answers

Phillips Magnovox

Hi,

Its a power supply issue the only solution is to get it repaired.Possible power outage.Repair charges would be around $400.

Goodluck,
Please don't forget to rate the solution

Apr 25, 2008 | Philips 9P5034C 50" Rear Projection...

1 Answer

At start up, tv comes on, sound and picture. A few minutes later, the picture goes off, the on/off switch begans to flash and you lose the picture. Sound stays on. A few minutes later the picture comes...

Your Lamp needs to be replaced.
Mats Electronics 1-800-628-1118 they have Lamps for $89.95

Feb 27, 2011 | RCA HDLP50W151 50" Rear Projection HDTV

2 Answers

My Loewe Aconda TV will not turn on - buzzing noise.

My Loewe Aconda 81 HDR TV will not turn on. When I press the power button the green light comes on but the red light stays on with it and after a few seconds the green light goes out and the red light stays on. Any help please.

May 15, 2010 | Loewe Aconda ACO9383 38" TV

1 Answer

Check engine light stays on ,auto zone read out indicates ox sensers , replace all sensers, checked fuse, replaced gas cap, checked wires , cleaned grounds,have power all sensers.one wire, ?????

the light has to be turned of by a chevy specialist using a computer

Feb 03, 2010 | 2004 Chevrolet Blazer

2 Answers

NAPA welder model 38-328 continuesly feedswire

is there power at the wire all the time. if so the finger switch may be stuck or shorted

Oct 22, 2009 | Welding Tools

1 Answer

Some times the van will start then sometimes I may turn it over and it wont start I can continuesly turn it over and it will then all of a sudden it will start and it sound like a valve is ticking it will...

SOUNDS LIKE YOU NEED TO REPLACE THE THROTTLE POSITION SENSER.GET THE CODES READ TO CONFIRM. AS FOR THE VALVE NOISE,YOU MAY HAVE A STICKY LIFTER,TRY SWITCHING TO A THINNER OIL OR MAYBE TRY SYNTHETIC.

Sep 28, 2009 | 1997 Plymouth Voyager

1 Answer

No picture

turn hard switch off in the back of the unit. Then put your finger on the soft switch on the front of the unit. While keeping your finger on the soft button in front, switch the hard button in the back to the on position and keep finger on the soft button for 10 secs, this will reset your vid settings.

Nov 15, 2008 | Sony Playstation 3 (PS3) Console

6 Answers

Dyson animal, have to hold ON switch for it to work

Pull the wand out of the Vac. Need to use a small Torx bit to take out 2 screws hidden behind the wand storage. Once screws are out, there are 4 push-clips which need to be un-latched. Pry the power panel off and you will expose the two switches (one for power, one for the brushes). Push the power switch down and it should "release" and go back to clicking when pushed. Re-assemble. Took about 5 minutes to fix.

Aug 06, 2008 | Dyson DC07 Animal Bagless Upright Cyclonic...

1 Answer

Help..... Phillip Magnovox Model 9P5034X101

NOT EXPENSIVE POWER SUPPLY PARTS ARE NEEDED TO BE REPLACED . ONLY A TECH WHO , HAS EXPERIENCE ON THIS TV MODEL AND THE KNOWLEDGE ABOUT THIS PROBLEM ,COULD FIX THE TV RIGHT THE FIRST TIME. OTHERWISE REPLACE POWER DEFLECTION BOARD ,PARTS AVAILABLE AT PARTSTORE OR SIMILAR COMPANIES

Apr 25, 2008 | Philips 9P5034C 50" Rear Projection...