Question about Rheem Gas Furnace 60000 Btu 95% Afue. Rgrc Model

1 Answer

Rheem furnace has 2 green lights 1 is slowly blinking

Posted by sklapenta on

Ad

1 Answer

Jeff Dimond

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

You can check the inside door chart, and it will map out the led light readout for you. just follow the instructions on the panel and it will tell you possible problems and what you may need to fix to make your unit run correctly.

Posted on Nov 20, 2012

Ad

5 Related Answers

Anonymous

  • 92 Answers

SOURCE: Ruud achiever 90 plus won`t start at times

sounds like you have a heat pump heat pumps dont work below 30* temps you should have some type of backup heat

Posted on Feb 05, 2009

Ad

Anonymous

  • 96 Answers

SOURCE: No Heat and I'm Cold

Your preasure switch is closed

Posted on Dec 05, 2008

atocrxr

Paul

  • 144 Answers

SOURCE: 2 Rheem Protech 500 thermostats, 1 upstair & 1

Have you checked to make sure that all of the supply registers are open, the air filter is clean and nothing is blocking the return air grill?
It almost sounds like you could be cycling on a limit switch.
Usually on gas furnaces, the blower is controled by the onboard controls, in the cooling mode the thermostat will control the blower.
I would be looking past the thermostat, at the furnace it self.
I hope you find this helpful. If you continue to experience problems, please let us know and we will dig deeper. :)
Paul

Posted on Apr 04, 2010

SOURCE: have a rheem 90 plus gas furnace, the problem is

Trunthe fan from the automatic position to the on position, if the blower does not come on then you
might have a relay problem. The relay is built into the
board, you may have to replace the board.

Posted on Jun 14, 2010

SOURCE: Have a rheem 90 plus gas furnace the problem is

At your thermostat turn the fan from auto to on, if the blower motor still does not come on, down at the furnace remove the blower door, turn power off first. Locate the blower motor leads, switch the cool lead which is usually black with the blue wire which is usually medium high.
Make sure while you are at it to see if the blower motor will turn by hand. Put door back on turn on power, leave the fan switch to `on` still. Blower should turn on. If not then either the blower motor is either burned out or you have a line/lolw voltage wiring problem.
You did not state if the outdoor ubit was operating, that will make it easier to troubleshoot.

Posted on Jun 17, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rheem furnace ,2nd green light blinks 5 times then pauses. I have only 1 furnace,not a twin


5 flashes is a "neutral polarity failure".
on the motor:
White is the neutral and must be plugged in to one of the 3 neutral slots on the control board (usually on the left side of the board)
The other 4 wires (black, red, yellow, brown) are power to the motor and should be connected to the appropriate pins on the control board.
ref: http://www.rheem.com/docs/FetchDocument.aspx?ID=d0613a32-db55-4e32-abfd-04e89e72f7a6

Sep 13, 2014 | Heating & Cooling

1 Answer

Protech 62-24084-02 troubleshooting


62-24084-02 LED CODES
POWER LED - GREEN
ON - Normal
OFF - No power to board
OK LED - GREEN
One Blink - One hour retry delay
Two Blinks - Pressure switch failure (remains open)
Three Blinks - Limit switch fault
Four Blinks - Pressure switch failure (remains closed)
Five Blinks - Twinning fault
FLAME LED - YELLOW
ON - Good flame
Rapid Blink - Flame present with gas valve de-energizing
Slow Blink - Marginal flame

Jan 01, 2014 | Protech Rheem/62-24084-82-1PK - Integrated...

1 Answer

My rheem cri II furnace will not work unless I turn the gas valve knob from on to off and back. The green led light is blinking then solid when I reset knob. Any ideas?


The green light is flashing an error code. When you turn the knob off and back on you are resetting the safety. Look for the number of blinks in a row. Then find the legend for codes on gas valve or on furnace. When is the last time you changed the air filter? A dirty filter can cause this problem.

Nov 07, 2009 | Heating & Cooling

3 Answers

I have a Rheem Criterion II Gas furnace. It is not igniting.  When I switch the thermostat to "heat" - the furnace doesn't not start.  There are 2 green lights - one is one and the other is blinking.  The...


Roscoe007 shouldnt speak unless he knows what he is talking about, as a heater installer i am telling you the ignitor needs to be replaced, the very fact that the ignitor does light for about 30 sec than goes out rules out any issue with the themostat, replace the ignitor!

Dec 13, 2008 | Water Heaters

2 Answers

No Heat and I'm Cold


Your preasure switch is closed

Dec 05, 2008 | Heating & Cooling

2 Answers

No heat and I'm cold.


Do you have the code reference on your furnace door? If so what does it say? The furnace has locked itself out, and we need to determine what in the world it needs..

Dec 05, 2008 | Heating & Cooling

Not finding what you are looking for?
Rheem Gas Furnace 60000 Btu 95% Afue. Rgrc Model Logo

3,976 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rheem Heating & Cooling Experts

Lawrence Oravetz

Level 3 Expert

10548 Answers

ray gallant

Level 3 Expert

71004 Answers

Marat Brikov

Level 3 Expert

515 Answers

Are you a Rheem Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...