Lights flashing on clean. Program does not take.

Kitchenaid: KUDE03FTSS1. Cleaning light pulses 6 times plus 1 1. Dishes not drying and wash cycle shutting down before finishing the complete wash cycle. Check door switch, ok. Check heating element, Ok at 14 ohms. Got to thinking, the Logic part of the mainboard must be working. It diagnosed itself. Remove K3 relay from W1019358 main electronic board. Took the plastic cover off the little 5-volt relay. Applied 5 Vdc to the coil, it worked. Found pitted contact points on the relay. Erratic continuity on contact points.
I purchased 10, JS1-F-5V relays from an online electronic parts store. 10 relays shipped to my door $23.00. A new board could cost from 175.00 to 350.00. I also replaced the K2 Pilot relay. it was the same relay as the Heater K3 relay. The Dishwasher works great. The active parts general go bad. I had a Whirlpool dryer, found the heater element relay went bad on its board, replaced it for $4.50 I guess I got lucky on this dishwasher , too
Stay Safe

cycle can take 2 hrs to complete. give it time,

Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Waterwill not drain out

heatman101

To Set the Cycle Completion Signal Tone Level
• With the "CLEAN" and "SANITIZED" and "RINSE AGENT" Indicator
Lights flashing.
• Press the "Tone Level.
• As you press the "Indicator Lights illuminating and the Cycle Completion Signal
Tone level changing.
o If none of the Wash Cycle Indicator Lights are illuminated,
there will be no tone. The Cycle Completion Signal is turned
off.
o If one of the Wash Cycle Indicator Lights are illuminated,
there will be a low Cycle Completion Signal Tone Level.
o If two of the Wash Cycle Indicator Lights are illuminated,
there will be a medium Cycle Completion Signal Tone Level.
o If three of the Wash Cycle Indicator Lights are illuminated, you
will be at the maximum Cycle Completion Signal Tone Level.
• Press "START" to save your settings.

Shut the breaker to the dishwasher off for 2 hours then back on, this will give it a reset. Your problem was caused by a power spike

you need to pull the dishwasher out and check your heating element.
to remove code hit heated dry and normal wash and toggle till all the lights light up and then hit cancel this should clear your code.
there is a problem with the heater or the heater curcuit
let me know how it goes

maybe a power surge. have it be the power coming into machines. let me know if this helps

I have DWT10P dishwasher.It is displaying two rapidly fashing E lights (Fast & Delicate )wash cycle.Can you tell me what its mean?

If the clean light flashes 7 times, pauses, then repeats...

When the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive). It does this as a safety in case the element is broken and feeding electrical current into the water.

To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cycle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring). It's not as common but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).

My dishwasher Indesit DI67S will not run on the number 1 cycle. It will fill and then when that programme finishes it jumps straight to the drying cycle missing all the rinses out etc. If on the number 2 programme it goes all the way through but then doesn't dry. I've also noticed that the water doesn't seem to be heating up much and certainly isn't drying. Is this the element or something else? Once its reached the drying cycle the light for this just flashes then I have a job to try and reset the machine. It can take endless attempts. Will switching the machine off at the mains solve anything or is it the element?
Thankyou