Question about Yamaha YST-SW216 Subwoofer

Open Question

Yamaha YST-SW216 connection

I have connected my SW216 to my Yamaho YSP-800 and the SW216 does not put out sound. It respondes to tapping the opposite end of the cable but still no sound. I have run auto setup and manual set up to enable the subwoofer. Still no sound. Any ideas? Thank you, Paul

Posted by paul adams on

  • Bart1 Jan 06, 2008

    I have connected my SW216 to my Yamaha YSP-900 and the SW216 does not put out sound. It respondes to tapping the opposite end of the cable but still no sound.

    I have run manual set up to enable the subwoofer. Still no sound.

    Any ideas?

    Thank you,

    Bart

×

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Yamaha YST-MSW10 subwoofer quits after about 10 minutes

This speaker has a feature that shuts it down automatically when there is no audio signal present for a period of time. Unfortunately, the threshold is set a bit too high so, if you're listening at low volume the speaker will turn off even if there is signal present.

I found this posting because I was looking for a circuit diagram so I could bypass the auto-off feature on my MSW10.

Posted on Nov 03, 2007

Ad

Anonymous

  • 238 Answers

SOURCE: Yamaha YST-SW150 Subwoofer

hi, is it a humming noise ??? check if the connector is plugged in properly,check the earthing, if its a three pin mains plug, if its a two pin, then the CPU SMPShave a proper eathing. let me know

Posted on Jan 12, 2008

Ad

Anonymous

  • 86 Answers

SOURCE: Power Subwoofer doesn't work

Two possibilities:
1. Your source material does not contain bass frequencies.
2. Your SUBWOOFER SET - BASS OUT is set to Front, rather than SWFR (subwoofer). See page 63 of the manual.

https://www.yousendit.com/download/dVlvdFdaY3lJMHZIRGc9PQ
or
http://tinyurl.com/csw8sy

Let me know if that helps.

Posted on Apr 19, 2009

stwill2326

Steve Williams

  • 77 Answers

SOURCE: connecting an iPod to Yamaha YSP-1000

The best way to get quality sound would be to go through the USB connection of the phone.

It will be hard and a bit costly to get a cable to link the Ipod and projector.

Easiet and economical way is to go to apple and purchase a cable for the jaudio jack at the top of the Ipod that will also have an audio jack connector for the projector

Posted on May 31, 2009

Marek Podmaka

  • 127 Answers

SOURCE: need a hookup diagram for yamaha rx-v461 plus

Hi,
Here you can find the manual for your subwoofer. Looking at its back side, it has 2 RCA plug input for stereo. Receiver has just mono sub output, but as low frequencies are not easily locatable, mono is perfectly OK.
Just connect receiver SUB-OUTPUT with RCA cable to your subwoofer's RCA LEFT input. Then adjust volume to match rest of your speakers.

Posted on Mar 02, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Yamaha ysp-800 stuck on mute, volume indicator just flashes

Did you ever get a solution to this? mine is doing the same. i press the mute button and it says audio mute off but no sound still and volume indicator keeps on flashing.
0helpful
1answer

Connecting an iPod to Yamaha YSP-1000

The best way to get quality sound would be to go through the USB connection of the phone.

It will be hard and a bit costly to get a cable to link the Ipod and projector.

Easiet and economical way is to go to apple and purchase a cable for the jaudio jack at the top of the Ipod that will also have an audio jack connector for the projector
1helpful
1answer

Need a hookup diagram for yamaha rx-v461 plus yamaha yst-sw216 please

Hi,
Here you can find the manual for your subwoofer. Looking at its back side, it has 2 RCA plug input for stereo. Receiver has just mono sub output, but as low frequencies are not easily locatable, mono is perfectly OK.
Just connect receiver SUB-OUTPUT with RCA cable to your subwoofer's RCA LEFT input. Then adjust volume to match rest of your speakers.
1helpful
1answer

How do I connect a mac audio output to a yamaha sound projector?

NO!!! get a 3.5 male TRS to stereo RCAs to either the Aux input on the amp or the audio portion of the front A/V Aux. the audio jacks will be red and white.
0helpful
1answer
0helpful
1answer

Can't get my YSP-800 to display on TV

More details on the connection you are attempting could allow someone to help you.
1helpful
2answers

Yamaha ysp 800 setup

can you please help me i have no set manual for ysp-800 and can you assist me on how set the microphone up to get the best sounds thanks
Not finding what you are looking for?
Yamaha YST-SW216 Subwoofer Logo

Related Topics:

260 views

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

The Knight
The Knight

Level 3 Expert

76791 Answers

Paul Bade

Level 3 Expert

1688 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...