Samsung ML 1210 Laser Printer Logo

Related Topics:

Question about Samsung ML 1210 Laser Printer

1 Answer

Error msg Samsung ML 1210 printer won't print. Error light is flashing along with all other lights. Is there a way to reset or is this printer simply gone?

Posted by jacque look on

  • Anonymous May 26, 2008

    My Samsung ML 1210 printer has a problem in which all of the lights will flash together. The lights start flashing AFTER the printer goes into what I call "standby mode". (After the printer is warmed up, and you have not printed anything for awhile.) Once the flashing starts, I cannot print unless I power the printer off and on again, and print before it goes into standby mode again.

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

Hi Usually with this printer, you just simply turn it off and then on again and the lights will stop flashing. This is an LSU (Laser Scanner Unit) error. If you still have the problem, it might be either the LSU needs replacing or it could be the main board. These parts might be scarce though and very expensive. It might almost be cheaper to buy new printer but that is up to you to check and decide for yourself.

Posted on May 25, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

All lights are flashing on samsung ML1210 PRINTER PL HELP

• Reset the printer by briefly turning the printer off and back on again.
• If the error persists, contact a service representative.
1helpful
2answers

Error light is red, and nothing prints

i think your paper sensor is damaged, replace it

red light show : when paper is not present or toner is not accepted, or door open


We have Zero cost solution for samsung -scx-4300, scx-4824/4828
ml-2240,ML 2245, ml 1640. clp 310/ 315, It is working permenently.
Refill cartridge is working for ever. which is running successfully.
also provide other new model reset solutions.

www.nakshatraworld.com

mob: 9713862555, 9893282285
[email protected]
3helpful
2answers

I have riffile my smasung ml-1640 printer cartage three time then it show red light but printer works ok, after 2100 pages printed its not working properly, when i give command to print any file no error...

By deepak_compu on Oct 06, 2009
i have riffile my smasung ml-1640 printer cartage three time then it show red light but printer works ok, after 2100 pages printed its not working properly, when i give command to print any file no error show,but print not come. and when i print a test page from printer button it gives print. but on paper write like this toner exhoasted so what i do for this problem please give me soltuion of this problem
0helpful
1answer

The red light then all the other lights flash alternately- nothing will print

• Reset the printer by briefly turning the printer off and back on again.
• If the error persists, contact a service representative.
2helpful
2answers

My samsung ML2010 printer has Error button flashing green

your printer is not inisilize properly. it is a logic card problem.so pls you can repaired it from printer vendor.
0helpful
1answer

Red light blinking, first orange then red, toner blinks green

dear sir
  1. it is problem paper miss feed
  2. over temparature
clean thermostator.thermostator over dry toner
or cartridge assembling problem
0helpful
1answer

Getting error on printer

Take out the cartridges and Perform a partial reset on the printer.

  1. Unplug the power cord from the unit.
  2. Reconnect the power cord into the unit.
  3. When the lights begin to flash, press and hold the On/Resume and Paper Size buttons.
  4. When only the On/Resume light is flashing, release the buttons. When the On/Resume light is steady, the reset is complete.
  5. Insert the cartridges and try the print job again to see if this step resolved the issue.
8helpful
1answer

Blank papers comes when the print given

D ear team, Blank papers comes when the print given. Meanwhile it shown the error msg is: LSU Hsync error cycle power pls give me the solution NHPC Ltd.
0helpful
1answer

REQUIRES YOUR IMMEDIATE ASSISTANCE

Both lights in steady blinking point to bad fuser (not good). If the unit is under warranty, take it to the nearest Service Center.
Not finding what you are looking for?

622 views

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

Cindy Wells

Level 3 Expert

6448 Answers

The Knight
The Knight

Level 3 Expert

76835 Answers

Muzahura Frank

Level 3 Expert

2071 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...