Fax number Hello, my fax machine is printing out the incorrect phone fax number when it's received by a recipiant. What to do? or how do I change it to the number it suppose to be.

1. Make sure the fax machine is plugged into a power source and also plugged into a working phone jack.
2. Turn the fax machine on.
3. Obtain the fax number of the destination fax machine.
4. Gather the documents you want to send and put them in the order you want them to be received.
5. Fill out a separate piece of paper called a coversheet with the recipient's name, fax number/phone number, your name, your phone number, a short message and number of pages (including coversheet).
6. Lay the documents face-up in the fax machine feeder tray with the coversheet on top
7. Dial the recipient's fax number - put 9 before the number and area code
8. Press the "fax" or "send" button, depending on the particular fax machine model

You can send a fax in a variety of ways. Using the control panel, you can send a black and white or color fax. You can also send a fax manually from an attached phone. This allows you to speak with the recipient before sending the fax.
To send a basic fax (single- or multiple-page black-and-white fax) by using the control panel.These features allow you to control the pace of your dialing. They are also useful when you want to use a calling card to charge the call and you have to respond to tone prompts while dialing. NOTE: If you need printed confirmation that your faxes were successfully sent, enable fax confirmation before sending any faxes. TIP: You can also send a fax manually from a phone or by using monitor dialing.
1. Load your originals. NOTE: If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass. 2. Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.TIP: To add a pause in the fax number you are entering, press Redial/Pause, or press the Symbols (*) button repeatedly, until a dash (-) appears on the display. 3. Press START FAX Black or START FAX Color. • If the device detects an original loaded in the automatic document feeder, it sends the document to the number you entered. • If the device does not detect an original loaded in the automatic document feeder, the Fax from glass? prompt appears. Make sure your original is loaded print-side down on the glass, and then select Yes.TIP: If the recipient reports issues with the quality of the fax you sent, you can try changing the resolution or contrast of your fax.

Send a fax manually from a phone You can send a fax from a telephone on the same phone line if you prefer to use the keypad on your phone, instead of the keypad on the control panel of the device. You can do this by plugging in a phone into the 2-EXT port on the back of the device. When you send a fax manually, you can hear the dial tones, telephone prompts, or other sounds through the handset on your telephone. This makes it easy for you to use a calling card to send your fax. Depending on how the recipient has their fax machine set up, the recipient might answer the phone, or the fax machine might take the call. If a person answers the phone, you can speak with the recipient before sending the fax. If a fax machine answers the call, you can send the fax directly to the fax machine when you hear the fax tones from the receiving fax machine.
1. Load your originals. NOTE: This feature is not supported if you load your originals on the glass. You must load your originals in the document feeder tray. 2. Dial the number by using the keypad on the phone that is connected to the device. NOTE: Do not use the keypad on the control panel of the device when manually sending a fax. You must use the keypad on your phone to dial the recipient's number. 3. If the recipient answers the telephone, you can engage in a conversation before sending your fax. NOTE: If a fax machine answers the call, you will hear fax tones from the receiving fax machine. Proceed to the next step to transmit the fax. 4. When you are ready to send the fax, press START FAX Black or START FAX Color. NOTE: If prompted, select Send Fax, and then press START FAX Black or START FAX Color again. If you were speaking with the recipient before sending the fax, inform the recipient that they should press Start on their fax machine after they hear fax tones.
The telephone line is silent while the fax is transmitting. At this point, you can hang up the telephone. If you want to continue speaking with the recipient, remain on the line until the fax transmission is complete.

Send a fax using monitor dialing Monitor dialing allows you to dial a number from the control panel as you would dial a regular telephone. When you send a fax using monitor dialing, you can hear the dial tones, telephone prompts, or other sounds through the speakers on the device. This enables you to respond to prompts while dialing, as well as control the pace of your dialing. TIP: If you do not enter your calling card PIN fast enough, the device might start sending fax tones too soon and cause your PIN not to be recognized by the calling card service. If this is the case, you can create a speed dial entry to store the PIN for your calling card. NOTE: Make sure the volume is turned on, or you will not hear a dial tone. To send a fax using monitor dialing from the control panel
1. Load your originals. NOTE: If you are sending a multiple-page fax, you must load the originals print-side up in the document feeder tray. You cannot fax a multiple-page document from the glass. 2. Press START FAX Black or START FAX Color. • If the device detects an original loaded in the automatic document feeder, you will hear a dial tone. • If the device does not detect an original loaded in the automatic document feeder, the Fax from glass? prompt appears. Make sure that your original is loaded on the glass, and then select Yes. 3. When you hear the dial tone, enter the number by using the keypad on the control panel. 4. Follow any prompts that might occur. TIP: If you are using a calling card to send a fax and you have your calling card PIN stored as a speed dial, when prompted to enter your PIN, press Speed Dial or a one-touch speed dial button to select the speed dial entry where you have your PIN stored. Your fax is sent when the receiving fax machine answers.

USER MANUAL Page 3-34
Press STATUS key 3 times. Press YES. Press UP and DOWN keys to select the report you wish to print.
TX Result Report The document number, recipient name, date sent, starting time of transmission, number of document pages, time required, mode.
RX Result Report The document number, caller name, date received, starting time of reception, number of pages received, time required, mode, and reception result are printed.
The machine can also be set to print this report automatically after every 60 transmissions/receptions.

Using the HP Network Diagnostic Utility in Windows - HP Customer Care (United States - English)

If you have the fax # correct, than it is the responsibility of the fax recipient to correct the situation. You cannot make a parametrical changes to someone elses fax machine. Thank you, Dana

The recipient may have a DSL phone line, or receiving to a fax server that blocks your area code.

Try just making a copy and see if you have the black lines on your copy (most fax machines have a basic copy function if it is you have dirty scan glass and on these small machines it is a real hassle to get too and clean Try Canned Air. If no black line on your copy it may be the recipients machine.

there is no need to change the setting.just feed the document to be sent and dial the number of the recipient.after hearing the fax tone press enter key

Receive Mode Setting
On the operation panel, press the following buttons to select the appropriate receive mode.

1. Press <Fax>.
   
   
2. Press <Menu>.
   
   
3. Press the right or left arrow button to select [Receive mode set], then press <OK>.
   
   
4. Press the right or left arrow button to select the receive mode that best suits your needs, then press <OK>.
   
   
   FAX ONLY MODE: When you want to receive only faxes automatically with your machine, or have a dedicated telephone line for FAX use only.
   
   MANUAL MODE: When you receive mainly voice calls and sometimes faxes, or want to receive faxes manually.
   ANS MACHINE MODE: When you want to receive voice messages on your answering machine and receive faxes automatically.
   FAX/TEL AUTO SW: When you want to receive faxes automatically as well as voice calls.
   DRPD: When you have subscribed to a DRPD service with your telephone company.
   
   
5. Press <Stop/Reset> repeatedly to return to fax standby mode.

Sending Methods

• Memory sending
• Manual sending

Sending From Your Machine (Memory Sending)

1. Load the document on the Platen Glass or the ADF.
   
   
   Sending from the platen
   
   Important: When sending a double-sided document, set the document on the Platen Glass. You cannot scan double-sided documents from the ADF.
   
   
   
   
   
   Sending from the ADF
   
   *MP830 shown
   
   
2. Press <FAX>.
   
   
3. Adjust the settings for your document as necessary.
   
   
4. Dial the recipient's number using the numeric keys or speed dialing.
   
   
5. Press <Color> for color sending, or <Black> for black & white sending.
   
   
   • When the document was loaded on the Platen Glass:
     
     
     1. When the following message is displayed, load the next page on the Platen Glass.
        
        
        
        If you have only one sheet to scan, press <OK>..
        
     2. Press <Color> to send in color, or <Black> to send in black and white.
        
        IMPORTANT: If you do not press the same button you pressed in step 5, the machine does not start scanning.
        
     3. Repeat steps 5a and 5b to scan in all pages of the document.
        
     4. Press <OK>.
        
        
   • When the document was loaded in the ADF:
     
     The machine starts sending automatically after the document is scanned in.
     
     Note: Color sending is available only when the recipient's fax machine supports color faxing.
     

• To cancel sending before sending a fax, press <Stop/Reset>.
• To cancel memory sending while sending a fax, follow any instructions on the LCD after pressing <Stop/Reset>.
• If the document remains in the ADF after pressing <Stop/Reset> during sending a fax, press <OK>. The remaining document is automatically fed out.
  
  

Sending From Your Machine (Manual Sending)
Use manual sending when you want to talk to the recipient before sending a document, or if the recipient does not have a fax machine that can receive automatically.
Caution:

• With manual sending, you cannot use the Platen Glass to send documents.
• You will need to connect a telephone to your machine if you want to talk to the recipient before sending a document.

Follow this procedure:

1. Connect a telephone to your machine if you want to talk to the recipient before sending a document
   
   
2. Load the document in the ADF.
   
   
   
   
   
   Sending from the ADF
   
   
3. Press <FAX>.
   
   
4. Adjust the settings for your document as necessary.
   
   
5. You can lift the handset if one is connected to the machine.
   
   
6. Dial the recipient's number using the numeric keys or coded speed dialing.
   
   
7. Talk through the handset to the recipient. (If you hear a high-pitched signal instead of the
   recipient's voice, go to step 9.)
   
   
8. Ask the recipient to set recipient's fax machine to receive faxes.
   
   
9. When you hear a high-pitched signal, press <Color> for color sending, or <Black> for black & white sending. Then hang up the handset.

the solution given is correct. happy faxing OMNIPRESENT