My Enter Mp3 player not starting , when I switch it on , on displays as staring and it remains in that state only

You could try the following:

Start with the Clip turned OFF. Slide the power switch down to the HOLD position. Press and HOLD the center button depressed until it is recognized by the PC- give it a few seconds.

The Clip's display will state "connected" with the device now in MSC mode.

You can now repair the File Allocation Table (FAT) using Windows' chkdsk utility.

Open My Computer and find the Clip a listed under "devices with removable storage" as a flash drive. Let's say it displays as E: SANSA CLIP for example. Our assigned drive letter is E:

From the Run box under Start, enter cmd and press Enter. You will get a DOS window.

Enter chkdsk E: /f and press Enter. The /f toggle tells the utility to fix the errors.

After clicking on the Safely Remove icon in the taskbar, or right clicking on the Clip and selecting Eject, unplug the Clip.

Try powering it up again, and see if all is well.

I found this at: http://forums.sandisk.com/t5/Sansa-Clip-Sansa-Clip/FAT-is-corrupted-On-Clip-4G/td-p/250798

Hello,
Connect the player to your PC. Start windows explorer and find the drive "removable disk". Select this drive, right click on it and choose "format". Then you get to a window where you should simply click the "start" button.
If your player remains in blocked state you will need to upgrade the firmware.

Bye, gylacz

Hi there

You computer is probably frozen but this is how to solve the problem

Flip the MP3 player's "Hold" switch to "Off" if the switch is on. Depending on the MP3 player you own, this switch is likely located at the side or top of the player. Once the switch is off, try to turn the player on.

Let the battery of the MP3 player die. A frozen MP3 player is technically still running, and thus the battery for that player is being drained. Wait until the battery is fully dead before moving to Step 3.

Charge the MP3 player using either a computer (that's turned on) or an electronic MP3 charger. Charging the player's battery may "jolt" the player out of its frozen state. Connect the player to the computer or charger via the player's USB cable. Charge the player for 30 minutes before attempting to turn it on.

Sync the player with the appropriate software program (for example, Windows Media Player) for the MP3 player. Connect the player to the computer as described in the previous step. Open the software program and click the "Sync" tab at the top or side of the program. If necessary, click "Start Sync" underneath the tab. The name of the player appears under the "Sync" tab if the player has synced successfully. Try turning the player on once it has synced with the program.

Press the small "Reset" button on the MP3 player. This hard reset shuts the player down completely. Use a pin, tack or thin nail to press down the very small "Reset" button on the side or back of the MP3 player to reset the player. Then, try to turn the player on.

sir i have micromax v8 mp6 player. Made in china. i have problem that when i switche on the start butten just the green light lit it but the display remains dark.It also did not detected at any USB Port at any system.

Transcend Tsonic 650 2GB mp3 player not starting up and not responding.. When I try to switch on the player, its not at all switching on.When I connect it to my PC, it shows busy symbol on its display and not responding from there on. Also its not getting recognised by PC. Please help me.

go to site enter mp850 then serial no then download firmware.
i will research the steps to restore so it will be recognized on computer and email it to you http://www.transcendusa.com/Support/FAQ/index.asp

The solution to a Code 10 error is to disconnect the mp3 player from your computer, uninstall all of the Philips software that came with the device, restart your computer, reinstall the Philips software, and THEN and only then - connect your mp3 player to the computer.

-Tha Mp3 Doctor

Transcend Tsonic 650 4GB mp3 player not starting up and not responding.. When I try to switch on the player, its not at all switching on.When I connect it to my PC, it shows busy symbol on its display and not responding from there on. Also its not getting recognised by PC. Please

1) See if hold button is not enabled.

2) If problem still persists, than reinitialize the firmware with deriver CD provided with it.

Try fully charging