An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 20 times.
An expert who has answered 20 questions.
Re: how to install a panasoinc cq-df903u in 91 integra
The wires for the two harnesses should be color coordinated or at least closely colored. The harness should have come with either a guide that says what is what or the wires themselves have little flags saying what they are. You can use this to match it up with CD Players wires by using the manual from the CD player to know which wire is what.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There are wiring kits you can buy that have the proper connectors on both ends of the wire harness so it will match up with the radio and the car's wiring harness. No cutting or splicing involved. Just push the connector into the radio and the car's original radio plug connector.
OK, first I recommend you purchase a wiring harness specific to the vehicle. The wiring harness is equiped with standardized wire colors to match aftermarket radios. Then the harness plug situates the wires in the correct pattern to match the vehicle. All you do then is plug it in. You will probably need a trim panel too. I recommend you check out www.crutchfield.com, they have the harnesses, dash kits, and instructions. Hope this helps.
The following should help you. Good luck. Please rate.
Factory Amp Turn-on
LF Speaker +/-
tan - black
Notes: If equipped, the amplifier is in the passenger side of the trunk.
RF Speaker +/-
blue - red
LR Speaker +/-
white - brown
RR Speaker +/-
orange - green
For the stereo the following will work.
Im quessing you are trying to install a sony radio into your jeep. The question is do you still have a plug on the wires in the dash? Or has the plug been cut off? If you still have the plug-you can buy a wire harness from Best Buy or Crutchfield or any car stereo shop that will match the wires for you. If you need more info on how to install this radio without the harness, e-mail me cuz it's alot of typing for nothing if you don't.
Radio Constant 12V+ Wire: White/Green Radio Switched 12V+ Wire: White/Red Radio Ground Wire: Black Radio Illumination Wire: n/a Radio Dimmer Wire: Red/Black Radio Antenna Trigger Wire: n/a Radio Antenna Location: Rear Glass Front Speakers Size and Location: 6 1/2′ Doors Left Front Speaker Wire (+): Blue/Green Left Front Speaker Wire (-): Gray/Black Right Front Speaker Wire (+): Red/Green Right Front Speaker Wire (-): Brown/Black Rear Speakers Size and Location: 6′ x 9′ Rear Deck Left Rear Speaker Wire (+): Blue/Yellow Left Rear Speaker Wire (-): Gray/White Right Rear Speaker Wire (+): Red/Yellow
you will have to go to the gm garage and ask for the wiring diagram to match the wires up. but the way to fix it the right way is to go to the junk yard and cut the harness out of a car and splice the wires back together then go to wall mart or best buy to get the right wiring adapter then you can match them colors up to your new radios wires and plug into your car
You need an installation harness. You can get them at most anyplace that installs car stereos. Once you have the installation harness for your car, you just match up the colros of the wires on it to the same colors of the harness for the Pioneer. Make sure that each wire is insulated from anything by using some electrical tape and make sure they all have good connections. Strip away close to about an inch on each wire and then twist them together and then tape them good. After all the wires have been connected, all you need to do is plug the Pioneer harness into the Pioneer radio and then plug the installation harness into the factory wire harnees connector in the car. If you have any wires that do not match up in color, you can normally leave then not connected to anything, but make sure they are insulalted with electrical tape. Most all the wires should say what they are for. Matching the colors is the easiest way to do this.
Let me know if you need more help. I can always give you a detailed wiring of the Pioneer. I do not have the wiring diagrams for the car though.
Best thing to do is purchase a Radio Wiring Harness. These can be purchased at a Store like Circuit City, Best Buy, WalMart (not sure of your location) or a 12 Volt Specialty shop.
This harness will connect to your new radio harness and plug directly into the vehicle harness without having to cut wires. The Radio Wiring Harness will come with color identification to match to your radio harness.