Question about Koiiler XM-7676W Car Audio Amplifier

3 Answers

Need help in wiring speakers to amp.

I have a Koiiler XM-7676 amp, but I don't know how the wires are connected from 10" subwoofer speakers(4ohms) to amp. And how the power is distributed even between both speakers. I tried connecting them, but got one speaker sounding louder then the other. Obviously one is getting more power than the other. On the amp you got R+,L- and R-,L+(bridged)terminals. How do i connect the speakers to amp with even power? Any help is appreciated,thanks.

Posted by Juan Zavala on

Ad

3 Answers

Mike Duncan

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 219 Answers

The right speaker will connect to the R+ and R- terminals and the left speaker will connect to the L+ and L- terminals. Only one speaker per connection. If both speakers are not exactly the same brand, part number,size, etc. then they may NOT sound the same. Be sure to watch the polarity of the speakers so they don't interfere with each other. I.E. speaker + to amp + etc. Good luck.

Posted on May 11, 2007

Ad

Anonymous

Moost conected R+endR-& L+endL-you moost respected polariti of wofer

Posted on May 11, 2007

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I just got a koiiler 7676 and need to wire it to a 4 ohm fosgate sub. how do i bridge the amp? Is there a button or switch that I need to move? or do I just wire them up as shown on the terminals?

Posted on Aug 12, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What rms is a koiiler 2000 wats amp

Koiiler xm 9767 2000watt amp anyone know rms on it. Is it a decent amp
0helpful
1answer

I dont know how to conect my subwoofer to the box,, because it has 2 coils

Friend,

Please visit rockford foshgate web site and look for wiring wizard.
From there you will know as to how to connect the wire to your speaker.

Using the 2 voice coil is a must in order for you to get the best result and best performance of your speaker.

Before connecting the wires of your speaker please see the load required from your Power Amplifier.

Please take note that most of the Power Amp. (CAR) need 4ohms load.



Regards,

peybols
0helpful
1answer

I need to bridge a koiiler 7676 to connect it to a 4 ohm sub. IS there a switch I need to move or do I just connect it using the speaker terminals as shown?

amplifier is tri mode ready. Just connect the speaker wires as shown for bridge configuration. Make double sure that you have a 4 ohm load in bridge mode.
1helpful
1answer

Need wire diagram koiiler xm 7676

U CAN GET ALL UR WIRE DIAGRAMS FROM PIONEER WEBSITE JUST OUT IN UR MODEL NUMBER THEN TYPE IN WIRE DIAGRAM
0helpful
1answer

Koiiler XM8787 Amp power problem

Sometimes i goes into protection when the amp is overloading with power.. Or the amp is touching metal.. Or the ground wire aint in the right place..Or check your RCA's, Speaker wires? if their earthing your amp..
0helpful
1answer

I want to know the best subwoofer wiring diagram for three kicker cvr 10 inch subs, 2 of them are dvc 4 ohm and 1 is dvc 2 ohm, the amp that i am using is jl audio 500.1 1.5-4ohms stable. can anyone help...

if the amp has a 2 outputs then i would wire the two 4ohms together, and the 2ohm by itself. and if its a 4 channel output then wire them all sepretly, if its a 1 channel output then wire the two 4ohms together and leave the 2ohm sub out
1helpful
1answer

Wiring hk12x2

Hello jose08042008,

Your sub has dual 2ohm voice coils and can be wired to present a final load to the amplifier of either 1ohm or 4ohms. Unless you have an amp that is stable at 1ohm (not many are), then you will want to use the 4ohm wiring. To wire for 4ohms, jumper the positive terminal of one voice coil to the negative of the other terminal, and connect the remaining positive and negative terminals to your amp. If you know for SURE that your amp is stable at 1ohm, you can connect both positives and both negatives together on the sub and then to the amp. But if the amp 1ohm stable, this will result in overheating, and/or going into "protection" mode, and/or damage to the amp.

Hope this helps.
2helpful
1answer

Wiring 12" icmb-5612 preformance teknique subwoofer

That sub has dual 4-ohm voice coils. It can be wired either as 2-ohm, 4-ohm, or as 8-ohm.

2-ohm = voice coils in parallel (both positives and both negatives connected to your speaker amp out wires).
4-ohm = use only 1 voice coil (either is OK).
8-ohm = voice coils in series (connect the positive of one voice coil to the negative of the other and connect the remaining positive and negative to your speaker amp out wires).
0helpful
1answer
0helpful
1answer

Amp not getting any power after replacing deck.

If the amp doesn't power on at all after switching the deck, the most likely problem is the remote turn-on wire. (The subwoofer options might prevent sound from reaching the amp, but it would still switch on). Where is the remote wire from the amplifier connected at the back of the new deck?
Not finding what you are looking for?
Koiiler XM-7676W Car Audio Amplifier Logo

Related Topics:

716 views

Ask a Question

Usually answered in minutes!

Top Koiiler Car Audio & Video Experts

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Morne Olivier
Morne Olivier

Level 2 Expert

264 Answers

Tom Chichester

Level 3 Expert

62199 Answers

Are you a Koiiler Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...