Question about Electrolux 23 in. ESI602X Built-in Dishwasher

2 Answers

Electrolux esi 602 dish washer - Spare Parts Availability?

Hi all, I have a Electrolux esi 602 dish (washer built in)the only problems is that the main control knob has come off, the sleeve (type) section at the back of the knob has broken, also the internal plastic spindle and the whole switch unit has dropped down. Is it possible to get this part, or just the knob so that I could replace it myself, the electrical connectors just appear to be simple pull off types? I am in the UK, all help much appreciated. Rickon

Posted by Rickon Nye on

  • Lainey7 Dec 13, 2007

    I have exactly the same problem

×

Ad

2 Answers

johnsrx8

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I've got the same problem.
Just found a site - spares2go.co.uk which suggests it might have the knob for £10.52.

If it comes, I'll update !

Posted on Jul 13, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same problem - is this site dead?

Posted on Jan 12, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Electrolux EIFLSS55IIWO Washer. The chrome paint on the selector knob is chipping so Electrolux is sending me 2 new knobs for the washer and matching dryer. Can you please advise how to replace...


Good Morning David,

I see that you are looking to replace the selector knobs for your Electrolux washer, model# EIFLS55IIW as well as your matching dryer. This is typically not a common DIY job, and I do recommend contacting an authorized technician. However, I have found a link on the manufacturers sister website, which I have listed below, that provides a parts breakdown. It will also allow you to enter in the model number of your Electrolux dryer and locate the parts breakdown, as well as, a comprehensive listing of authorized techs in your area. Hope this proves to be helpful!

http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=EIFLS55IIW0&User=&Search=Search

-Best Regards-
WP

Apr 07, 2014 | Electrolux EIFLS55IIW - Front Load Washer...

1 Answer

Electrolux dish washer error C03


Hello agusta_bjarn - Are you certain the error code is C03? Could it possibly be E03? If so, typically error code E03 indicates that there is a failure with either the wash motor or motor hall sensor. I suggest checking for suds in the tub and siphoning. A further diagnoses is recommended to have a professional check the wiring between motor and main control board since either part could need replacing.

Apr 12, 2013 | Electrolux 24 in. EDW5505EPS Stainless...

1 Answer

Electrolux washer displaying error code E5E


Communication problem. Check the wiring between the Main
Control Board and the Speed Control Board. Wiring bad, correct wiring problem. Wiring good, replace the Main Control Board. If the problem is not corrected, replace the Speed Control Board.

Dec 28, 2012 | Electrolux 134743500 Fridgidaire Washer...

1 Answer

ESI 602 dishwasher trips out the mains trip switch after a couple of seconds after turning on any solutions please.


needs looking at.........bad earth can cause trip
also the rear element or stats wire can short against the machine casing.......
cheers

Mar 27, 2011 | Electrolux 23 in. ESI602 Free-standing...

1 Answer

My Electrolux DW is not removing all the detergent on the rinse cycle leaving the dishes covered with residue. Any ideas?


Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101


=-=-

Jun 09, 2010 | Electrolux 24 in. EDW5500DSS Stainless...

1 Answer

Dish washer not draining


if neither are then its in the plumbing of the house

Jun 01, 2010 | Fisher and Paykel 24 in. DD-602 Built-in...

1 Answer

Electrolux ESI 602 will not fill with water


The float better be inside the tub, at the bottom, it usually only travels a couple of inches up and down... you may have a protective cover in the way of it.

Jul 26, 2009 | Electrolux 23 in. ESI602X Built-in...

1 Answer

Timer knob on washer broke off leaving the plastic sleeve attache


I did fix this problem myself, I found a heavy duty 'bread tie' type of wire, I tied it around the base of the stuck sleeve and wrapped the loose end of the 'bread tie' around my pliers and pulled very hard and it shot off like a bullet, I am now using my replacement knob..yeah for me..

Jun 12, 2009 | Crosley Washing Machines

1 Answer

Goes through cycles but does not clean dishes


Do you know if the washing arms are turning. Normally after the machine fills up the main pump begins and the washer sounds like it is washing dishes. If you carefully open the washer at this point (just a little) it will be eveident that water has been sprayed around inside as it will be dripping everywhere. If not you pump hasn't activated. This does not mean you pump is broken however it could be the pressure level switch sticking and not completing the circuit that starts the pump.

Apr 29, 2008 | Electrolux 18 in. ESL4114 Slim-Line...

Not finding what you are looking for?

Open Questions:

Electrolux 23 in. ESI602X Built-in Dishwasher Logo

Related Topics:

1,022 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Dishwashers Experts

Mike

Level 3 Expert

4372 Answers

Cindy Wells

Level 3 Expert

6234 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Electrolux Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...