Reset channels?? I own a Denon AVR 2700 (owned for 5+ years). Unfortunately, I lost the remote in a move & cannot reset the tuner stations. (I called Denon... a new remote was $100. & they couldn't help beyond that... didn't seem right). I tried getting a universal remote, but it would not work with the Denon. Help please - I can't listen to the radio because I cannot reset the stations. Any suggestions/ideas? Also, does anyone know a universal remote that might work? Thanks!!! art

Try pressing the Band button on the remote or on the AVR-1604. On the receiver, the band button is just below the left-hand edge of the LCD screen. To the right of the band button are the DTS button and the preset station buttons. There are no warnings about needing both the FM and AM antennas connected in the manual. Crutchfield has the manual for the AVR-1604 on the product page: https://www.crutchfield.com/S-uT0aFEwnSpF/p_033AVR1604/Denon-AVR-1604.html . The current link to the manual is https://pdf.crutchfieldonline.com/ImageBank/v20111011085300/Manuals/033/033AVR1604.PDF .

Denon's support site, https://denon.custhelp.com/app/answers/detail/a_id/3954/~/am%2Ffm-%28tuner%29-audio-reception , recommends having both antennas connected. A replacement FM antenna is fairly cheap. This one, https://www.amazon.com/Ancable-Replacement-Antenna-AVR-3806-3808CI/dp/B01LW5A7AU , looks similar to the one included with the original parts for the AVR-1604.

I hope this helps.

its just the amplifier problem

There is no module per se. Tuning is accomplished by applying a voltage to the tuner chip and their associated circuits. It needs to be repaired by a Denon service center.

If your Denon has optical input, you can. There is no problem.
http://electronicshelponline.blogspot.com/

www.remotes.com/store/denon/avr3801.html

here is a link to get new remote...this is only way to tune

14 INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the
microprocessor is required by the following procedure.
1 Switch off the unit and remove the AC cord from the wall
outlet.
2 Hold the following AUTO button and PCM button, and plug
the AC cord into the outlet.
3 Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 buttons
and the microprocessor will be initialized.
NOTES:
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from
the factory).
• Calling out preset stations from the main unit‘s panel.
1 Press the TUNING PRESET button. TUNING
PRESET
FUNCTION 2 Turn the FUNCTION knob and
select the desired station.
TV CD CDR/MD/TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
CHANNEL VOLUME
+
-
+
-
VDP DVD
TUNER PHONO CD
DISPLAY
SETUP RETURN
MENU
SHIFT
SURR.
PARA. OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
2 1
(Main unit)

I just tried doing it on mine from the panel and I could only change the presets

Help with hooking PS3 to a Denon Receiver. It worked before, but I had to move everything to a different location and when I hooked it back up the PS3 has sound but no picture. I have it hooked directly to the receiver with and HDMI cable (the receiver is hooked up to our cable box which is directly hooked to the tv via HDMI cable).

If you have the owner manual check for reset and reset the unit. If you don?t have the manual unplug the power cable for a wile and then try again. Good Luck Toufic Malek

If DIGITAL sign on the display blink, it mean the DSP board is defective. probably the DSP itself