Question about Whirlpool 24 in. DU1055XTP Built-in Dishwasher

1 Answer

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash

Posted by Angelia Hall on

Ad

1 Answer

Whirlpool

  • Official Brand Answer
  • 408 Answers

Angelia:
Thank you for your review.
We would like to inquire further about your review with you. Please respond back to this email address, [email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance.
We look forward to your reply.
Thank you,
Whirlpool® Social Media Relations

Posted on Mar 09, 2018

Ad

4 Related Answers

Anonymous

  • 1 Answer

SOURCE: whirlpool dishwasher # quiet partner II

Pushing and holding the 'Heated Dry' button should turn off the light over the padlock symbol and get you going again.

Posted on Jan 22, 2009

Ad
jsrock516

Jeff Rockwell

  • 5911 Answers

SOURCE: I have a whirlpool Quiet Partner I. HELP Drain light flashing

This may or may not help in your situation, but the following link explains how you can clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now...keep in mind all dish washers are not alike and have different panel options. If you do not have the same set up as I have referenced, the tech sheet for your dishwasher will explain. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Sometimes this can be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of which circuit is causing your problem. Again, refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this fixes your problem.

Posted on Jul 11, 2009

Anonymous

  • 262 Answers

SOURCE: Quiet Partner II Whirlpool Dishwasher 2 years old,

Unusual LED or

Display Readouts

Open ID diodes and/or LED

circuit(s) in keypad, or open

circuits on the control that drive
See "Checking Keypad Operation."

Press the following in sequence...Then try touch pad......
HEATED DRY ? NORMAL ? HEATED DRY ? NORMAL ? HEATED DRY ? ORMAL

here is the deal...if the touch pad is unresponsive after entering the above in sequence then you will need to change out the touch pad.

here is the link to your model....part number 1 on the drawing...there are three different ones....the difference is the color.Click on the link http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Dishwasher-Parts/Model-DU1100XTPBA/1198/0130000/W0702219/00002?blt=06&prst=&shdMod=

Here is a link that will show you the three differnet colors...I would order from these guys....1 year warranty on parts no questions asked
click on the link http://www.repairclinic.com/Touchpad-Parts?s=t-DU1100XTP-%3d%3dc63

Posted on Feb 28, 2011

danny Hendrickson

  • 2468 Answers

SOURCE: My Whirlpool Quiet Partner II

have you tried powering it down,shutting off power to the unit for 15 minutes,sometimes the electronics will glitch as a computer does,if this is to no avail,then try removing all connections from the interface(control panel) to the main control panel and clean each cable and re-plug in,then see if this solves your problem,otherwise it may be time to replace either the interface or main control board

Posted on Apr 08, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to reset wirlpool quiet dishwasher


To reset it, you will have to have the door open. It can not be latched. Press "Heated Dry," "Normal," "Heated Dry," "Normal" within three seconds of the first pressed button. Now close the door, this should reset your dishwasher.17 Dec 2012

SOLVED: Dishwasher whirlpool quiet partner I push start button - iFixit

https://www.ifixit.com/.../Dishwasher+whirlpool+quiet+partner+I+push+start+button+not...
or try this link.
How to reset wirlpool quiet dishwasher Google Search

Oct 28, 2017 | Dishwashers

2 Answers

HOW TO RESET MY DISHWASHER


All you can do is turn the power off at the power point, leave it for a few minutes and then switch the power back on.

Jan 11, 2016 | Dishwashers

1 Answer

Whirlpool Quiet partner V Dishwasher will not start no lights ,,,nothing


Try unlatched door and hit heated dry, normal, heated dry, normal all within 3 seconds of each ither. Close dior, latch and try again.

Mar 02, 2015 | Whirlpool Gold Series Quiet Partner Iv...

1 Answer

Does my whirlpol du1145xtpb1 dishwasherr need to be reset


SERVICE DIAGNOSTICS CYCLE
To start the Service Diagnostics Cycle, press the
following keys, in order, in less than 6 seconds, while in standby(power on but unit off):
Heated Dry, Normal, Heated Dry, Normal
To Rapid advance one interval at a time, press the Start key, noting that
unlike Standard cycles, the Diagnostics Cycle automatically resumes
after door openings and does not require pressing Start to resume.

Once the diagnostic cycle has run and shut off, run a normal wash cycle, empty and with no detergent, to reset the control to factory "normal" operation. Make sure there's plenty of hot water.


Read more: http://forum.appliancepartspros.com/dishwasher-repair/261055-whirlpool-quiet-partner-ii-clean-light-flashing-have-reset-still-flashing.html#ixzz2UOcsE2Yg
http://forum.appliancepartspros.com

May 25, 2013 | Whirlpool 24 in. GU3200XTP Built-in...

2 Answers

Whirpool dishwasher quiet partner 2 clean light blinking wont cancel or run a cycle


Hello,

press normal heated dryer normal heated dry normal the dishwasher should reset and start. You will need to check the heater this happens because the heater normally fails. Let me know,

http://www.appliancerepairlesson.com/

Mar 07, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool quiet partner III. Clean light keeps flashing clean.


Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.

Aug 29, 2009 | KitchenAid 24 in. KUDI02IR Built-in...

1 Answer

Whirlpool Quiet Partner 980


Bad control board ,replace it.

May 26, 2008 | Dishwashers

3 Answers

Whirlpool dishwasher # quiet partner II


Pushing and holding the 'Heated Dry' button should turn off the light over the padlock symbol and get you going again.

Jan 17, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

9 Answers

Whirlpool gu2400xtpt3


I too had Flashing Clean light and only responded to Cancel light by trying to drain. Whirlpool Model DU1145. I too got problem to clear by pushing High temp,Heated dry, High temp and Heated dry. All lights on display lit up then it went through sequences of all cycles.

May 14, 2006 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Whirlpool 24 in. DU1055XTP Built-in Dishwasher Logo

Related Topics:

1,023 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...