Washing machine problem

perhaps you need to contact Bosch website for tech support

Fabric Softener Compartment Full Of Water - White Goods ...

www.whitegoodshelp.co.uk > ... > DIY Washing Machine Repair Help

Jul 9, 2013 - The small fabric conditioner compartment in the soap dispenser drawer has a plastic cap or tube at the back for the water to siphon up through. ... Make sure the washer is level front to back as well as side to side. .... If the washing machinehasn't been used since there's always the possibility that the plastic ...

The fabric softener part of my washing machine drawer keeps ...

www.mumsnet.com > Topics > Housekeeping

MumsnetAfter each wash, the fabric conditioner part of the drawer is f. ... The fabric softener part of my washing machine drawer keeps filling with water ... Stopped using thedispenser compartment for fab softener and instead did I separate ... see if that clears it up and also try cleaning behind the drawer in case there is a blockage.

Washing Machine ' Fabric Softener ' Problem ' Won't Empty

I have this completely SOLVED, what you need to do is:-
Remove the drawer and look inside the drawer slot, at the top you will see loads of holes, in the middle you will notice a peice just above the fabric possition approx 2.5 inches long and 1 inch wide, It will have little clips either side. IT IS THIS PART THAT IS BLOCKED WITH GUNDGE!...You need to prize these clips apart and the middle bit will drop down and you can clean all the **** from it and you will of solved the problem. If you break the piece off dont worry because it will still clip back in place and function as it should.
NO NEED to revove the top and clean the pipes.
THIS IS THE SOLUTION...NO OTHERS WILL WORK!!!

Fabric conditioner drawer not emptying on my bosch wae24467 washing machine this video will show you how to keep your soap draw clear and how to service the parts Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.
And don't forget to like us on facebook

Hi from retired Englishman in SW France,
Sorry to ask and please don't take this the wrong way but did you manage to remove the whole dispenser drawer and clear out the siphoning tube in the conditioner tray when you cleaned the 'gunk' out? If not please try the following guidance notes, paying particular attention to the bit in bold near the end ;-0)
Remove the complete drawer. To do this you will have to do one of the following-

• Top catch- push down the lip/catch at the middle rear and pull the drawer out (that's how our Bosch one is removed)
• release the catches underneath (our daughter's Indesit) or
• lift upwards on the tray as it is coming out to clear the lip underneath.

One of these should enable you remove it
(I am having to guess some of the following!)
Once out identify which tray is for the conditioner- the others are simply 'chutes' and open-ended.
It will normally have some sort of cover over it which you must remove to expose the little stuck up pipe/tube. On some models there is just a small individual cap over the tube. The tube is down which the conditioner and water should siphon. It is likely to be blocked by 'gunge'- a mix of powder and conditioner. The whole of the tray, particularly this pipe and the bit which fits over it, must be completely clean and clear for it to operate correctly. It is worthwhile checking fairly regularly.
If this does not work, pull out the dispenser drawer far enough to be able to just see the softener tray, select the (final?) rinse and check that water is entering the tray. If it isn't there is a fault with the water distribution and an engineer call is required ;-0(
Good luck,
John C

fabric conditioner drawer is always full of water This video will show you how to keep your soap draw clear and how to service the parts
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

I would take the top off and locate the operating lever for the fabric valve as it sometimes gets stuck with soap goo
eric

FJS1225W Front Load Washer This video will show you how to keep your soap draw clear and how to service the parts
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

Try a "good quality" name brand liquid softener. Some softeners out there are real thick and settle out to be paste. This problem was encountered by me and since I changed to a real liquid, it went away.

If you can remove the dispenser from the machine try soaking it in HOT water. The fabric softeners can cause a wax like build up that can clog the dispenser. If the dispenser will not come out of the machine then pour Hot water into it, cycle the machine and repeat. It took a long time to clog and will take a while to remove the clog(several cycles). This will work but will take time. Mix water with your softener to keep it from cloging again, it will thin the softener and stop the build up. If you add 50/50 water/conditioner shake well and use twice the normal amount so you are getting the full amount of softener/conditioner into the washer. This will help i had a similar problem with my front loading washer.