Problem with K-jam, just found out that it not working and after pushing reset button I got a message " Press send to restore factory default, other keys to quit " But no matter what keys i press got no response from the unit. I tried to take the battery out and connect the charger but the problem stays the same.
An expert who has achieved level 2 by getting 100 points
Hot-Shot:
An expert who has answered 20 questions.
Corporal:
An expert that hasĀ over 10 points.
Mayor:
An expert whose answer gotĀ voted for 2 times.
Expert
76 Answers
Re: Power up problem
Here is how to hard-reset your MDA/Wizard using a key combo - courtesy of a smart T-Mobile tech support help desk guy who wrote a note about it as it's not in official help doc's:
1. Simultaneously hold down the Communication Manager and Voice Dial buttons and put the Soft Reset 'button' with the stylus tip - all at the same time.
2. You see a very scary looking black screen with white letters in System font reading something along the lines of ?Are You Sure? Press Send key to continue.?
3. When you push the 'Send' key, the Green pick-up the phone key process starts
4. Next you will see what made me smile like a kid - Formatting FAT partition and very briefly in matter of few seconds began normal first boot.
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1.press and hold comm manager button and voice command button on the device.at the same time use the stylus to softly press the reset button still keeping the comm manager button and voice command button held in and the following message will appear on the screen:I-mate k-jam hard reset soft reset hardreset softreset. step 2.release the two buttons and press the send button to complete the hard reset.
make sure backup your contacts just incase i know this works as i just dont it as i was typing to make sure lol let me know how you get on and please make payment as soon as possible
Remove the back cover and then pull out the stylus.
2. With the device turned on, press and hold the TALK/SEND and END buttons, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the TALK/SEND and END buttons until you see this message on the screen:
This
operation will delete all your personal data, and reset all settings to
manufacturer default. Press Send to restore manufacturer default, or
press other keys to cancel.
4. Release the TALK/SEND and END
buttons, then press the TALK/SEND button to perform the hard reset, or
press any other button to cancel the reset.
Follow the steps to reset the product.
A partial reset returns user settings to factory defaults. On some models, the reset also restores the default language and country/region settings.
Disconnect the power cord from the product.
Press and hold # and 3 while reconnecting the power cord.
When reset displays, release both buttons.
Try printing again.
If these steps resolved the issue , you do not need to continue troubleshooting
2:Touch the tools icon on the main screen. The tools icon is represented by a wrench surrounded by a blue circle.
3:Touch the "Settings" icon which appears as a wrench.
4:Push the "Restore" button at the bottom of the screen. A confirmation message will appear asking to confirm restoring the Nuvi to factory settings. Push yes to restore the factory settings ............................................................................................ Try this for hard reset .
Turn off Garmin device. Press down on bottom right corner of the touchscreen [ Don't let go ] , and then power on the GPS unit. You should be prompted whether do you really want to erase all user data, or asked if do you really want to start up in maintenance mode. Press “Yes” to reset (warning: all data will be erased and lost, so backup before proceeding) or enter maintenance mode.
Hello there Hi there you can try. Following step by step resetting canon Pixma iP90 :
Before resetting printer canon iP90, start with printer power off.
Press resume button coincide with power button.
While pressing power button, release resume button.
Press resume button 2 times and then release both button
Green LED indicator will blinking and then stopped blinking.
When the Power LED lights in green, press resume button 4 times.
Press power button and the printer power will off. Otherwise off, depress again power button.
And the turn on the printer again, your printer canon iP90 should be response as normal.
You may not see a paper jam.
This may work for you, it has worked for many here I given this advice so gave it a try it could work for you.
Generally when this happens, something has fallen into the printer, or a piece of paper has been jammed in there.
First step, remove the ink cartridge, and turn the printer upside down and gently shake it, see if anything comes out.
If nothing goes, or you can't hear anything rattling around, get a piece of cardstock paper (60lb or heavier) and gently push this through the printer, to see if it will help push out what might be stuck in there. And gave the rode that the ink slides on a good clean and maybe a bit oil on cloth and wipe the rod with it. Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
hello. i recommend that you do a factory reset as follows: With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see a message on the screen. Release the TALK/SEND, END and POWER buttons. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset. Once the restore screen appears press Volume Up to restore the device to its factory settings or any other button to cancel. Once complete press Volume Up to reboot.
This will wipe all the storage (not the sd card) and your device will be reset to default settings. Hardreset(option1)
Pull out the stylus.
With the device turned on, press and hold the VOLUMEDOWN and CENTER buttons, then press the RESET button with the stylus tip.
Continue pressing the RESET, VOLUMEDOWN and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel. Hardreset(option2)
You can also use Clear Storage to reset your device back to factory default settings.
On the ?TouchFlo3D Home screen, slide to the Settings tab and then tap All Settings or goto Start and press Settings.
On the System tab, tap Clear Storage.
Enter “1234” and then tap Yes.
Hardreset(option3)
Pull out the stylus.
Turn device OFF.
While pressing the CENTER button, turn the phone on with the POWER button.
Continue pressing the CENTER button until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
This works on at least some Verizon CDMA phones on which option1 will not work. Hardreset(option4)
Pull out the stylus.
With the device turned off, press and hold the VOLUMEDOWN and CENTER buttons, then press and hold the POWER button.
Continue pressing the POWER, VOLUMEDOWN, and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
(works with Alltel touch pro)
To perform a hard reset 1. Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left
2. Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Do a factory reset. Use a program like PIM Backup (http://www.pocketpcfreewares.com/en/index.php?soft=1806) Save
the backup to your memory card, or back it up and copy it to your
computer, the do the Factory Reset. You can then reinstall PIM Backup
after the reset and use it to restore most of the stuff on your phone
(contacts, call logs, text messages, etc.)
Factory Reset instructions:
•Hold down both soft keys (both above the send and end key's) and use
the stylus to push the reset button in between the volume key and micro
sd slot. Then the screen will turn on and tell you something to the
extent of press "Send" to perform a factory reset. Hit send, and your
good to go.
it does **** when things go wrong with your phone, but with a little patience, all will be well.
×