Jensen VM9510 Car DVD Player Logo

Related Topics:

Question about Jensen VM9510 Car DVD Player

1 Answer

Jensen vm9510 the pink wire is not responding with emergency brake.Even when I m parked the unit comes on,but a few seconds after PARKING comes on the screen,Itried to put the pink wire on the negative and problem still there

Posted by otello castagnanova on

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Attach the pink wire to the red power wire to see if unit comes on. If does then no attached correctly to emergencing brake wiring.

Posted on May 16, 2007

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Does the pink cable that says parking has to be connected to the parking or it could be in any other power cable with a switch

The pink cable is a safety lockout so you cannot watch video unless the parking brake is set. There are "bypass kits" available online, but I discourage using them. Even a momentary distraction can get you into dangerous situations...
1helpful
3answers

Need the parking bypass code for jensen vm9510

1: Go into AM/FM mode
2: Hit "setup" on the remote control
3: Enter 543210 on the remote, listening for the beep for each number entered
4: A new menu will appear. Touch the button that has the hammer/screwdriver on it in the upper left-hand part of the screen.
5: Select Brake bypass to "ON" and hit the "X" near the bottom of the screen
6. I am not responsible for whatever you do with this code!!!
0helpful
2answers

Product jensen uv8 nov. 2007 model in a trooper 1996 auto

Hi,

The pink wire in most instances is the DVD's sensor that the vehicle is not in motion and is parked. It then allows the DVD player to display the movie not the warning message nor the blue screen.
Your description "...pink wire on a bolt attached to the body..." indicates that said wire is constantly grounded. The DVD then cannot sense that the vehicle was parked. What this tell us is that the pink wire must first have a +12VDC before it is grounded. This changeover from + to 0 is the trigger. What is required is to have a single pole double throw switch. One end terminal is wired to ACC B+12 while the other to ground with the center terminal to the pink wire. Moving the switch from position OFF to ON (+12 to GND) simulates the parking brakes condition and will enable DVD playback.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

0helpful
1answer

How do i bypass the parking brake switch in order for my video to play

All you need to do is hook up the wire that goes to the emergency brake cable to a ground (anywhere that is metal).
0helpful
2answers

Parking brake

If you have the VM9410 then there is a way to play dvd's even when you are driving. You must ground out the pink wire in the harness. This allows you to watch dvd's even when driving. good luck!
1helpful
1answer

Trying to find the parking brake

YOU DONT NEED TO HOOK THE PINK WIRE UP JUST PUT IN A DVD AND TYPE IN 543210. THIS IS A BYPASS CODE SO YOU CAN PLAY DVD WITHOUT HOOKING UP THE PINK WIRE. YOU MUST HOLD DOWN THE 0 FOR 4 SECONDS WHEN PUTTING IN THE CODE.
3helpful
4answers

Bypass the parking brake for vm9412 jensen

Hit Setup On Remote.
Select Language.
Get Remote And Hit 5,4,3,2,1,0.
Listen For Beeps. Touch “Hammer/Screwdriver” Logo.
Select Brake Override
Switch To Brake Override “ON”
Now Hit Setup On Remote.

this works thank you for posting this.
derek
1helpful
6answers

Jensen in dash dvd monitors

jensen double din dvd monitor it a uv8020 model to bypass the e brake or parking brake
5helpful
3answers

Parking brake hook up

This wire goes to the "Hot" side of the parking break switch... When the Parking Break is put on, a switch is closed, thus putting an "Earth" on this wire.. Ya can often bypass this by connecting to earth. Sometimes this wire can be "Hot" +12v so B4 doing anything with unit "On" check this wire for any Voltage.
Not finding what you are looking for?

126 views

Ask a Question

Usually answered in minutes!

Top Jensen Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5099 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Marvin
Marvin

Level 3 Expert

85242 Answers

Are you a Jensen Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...