Yamaha RX-V800 Remote Control

Rav-212

a couple of subtitutes:

$133 and $55

http://remotes.com/remotes/servlet/rs?a=gmi&smodel=RXV800&brand_pn=YAMAHA_RXV800&mode=large&uuid=A13001399186991

or you could buy a whole RX-V800 WITH a remote for $136 delivered...

http://cgi.ebay.com/Yamaha-RX-V800-5-1-channel-500-Watt-Receiver-/260751483460?pt=Receivers_Tuners&hash=item3cb5ffe244

Try this advice first:

http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641

"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

What if you DON'T use the remote? Does it shut down when just using it?

If SO, you have a bigger problem.

If NOT, it sounds like the remote is hosed - sending a code to shut off.

Do you have another remote of any brand that you could set to do something simple, like change volume? Don't train it from the original, though, or it would do the same thing.

Description: REMOTE CONTROL TRANSMITTER FOR RAV222 RXV800/1000/HTR5280 Only Numbers are allowed Model#: HTR5280-exploded view Availability: Pre-Order Price: $82.68 (USD) Part#: V6283501
The remote for the RX-V800 is the same as for the HTR5280.
Please contact the manufacturer for ordering, or contact one of their distributors, whose info is listed below.

Hope this helps!

Page link:

https://www.yamaha24x7.com/yamahaoms/ViewSchematic.aspx?ModelNumber=359096&SearchString=HTR5280

Distributor Ordering Information: HERMAN ELECTRONICS
7350 NW 35th Terrace
Miami, FL 33122
Phone: (800) 938-4376
Fax: (305) 477-8087
URL: http://www.hermanelectronics.com/OEMSearch.asp?Manufacturer=yamaha
VANCE BALDWIN ELECTRONICS
7060 State Road 84, Building 12
Fort Lauderdale, Fl 33317
Phone: (800) 432-8542
Fax: (800) 552-1431
URL: www.vancebaldwin.com

(I have the RX-V659). Because the Yamaha remote has TWO SEPARATE buttons - power ON and power OFF (standby). This problem can't be fixed. There's a code to choose power ON and another code for power OFF. But one button can't be two buttons. Bad engineering\ design by Yamaha in my opinion

The volume keys should be working by default, but you may have volume punch through turned on (meaning the remote is sending signals for TV or CABLE volume function no matter what mode you are actually on). To unlock volume control for AUX mode, do the following:
1. Press and release AUX
2. Press and hold SETUP until the remote blinks twice
3. Type 993
4. Press and release VOL-
The remote should blink four times to confirm unlock.

email me .... [email protected]... ill send
you a copy of the codebook page... but let me try and locate it first, i have the same unit before. Yamaha code books are the same also to other models.

Reden

heres the manual hope it helps, i had the same problem with the replacement. its all in the dsp button. but check out the manual let me know if it helps. -NATE

Hey there fontdude, I will begin assuming you are running your a/v cable into your receiver and then out to the TV or Monitor. If this is the case, I suggest you run the video cable direct from DVD or VCR device to Tv/monitor. You can still run the audio through your receiver. The nature of your problem was probably related to video signal strength being weakened as it ran through your receiver. Good Luck! Let me know how it works for you.

it can be accessed via the main unit controls but you need to go through your manuals. Maybe you can get your remote repaired still... maybe not badly damaged caused by corrosion.

[email protected]