Question about Nordic Track Exercise & Fitness

1 Answer

Need a front roller for my nordic track exp 1000i

Model # NTTL09901 120 VOLT 60 HZ 11AMPS SERIAL # N611362

Posted by Patrick Rose on

Ad

1 Answer

ernesto cuadra

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nordic Track Master
  • 12,223 Answers

Posted on Sep 06, 2012

Ad

5 Related Answers

Ivectoru

  • 5 Answers

SOURCE: manual

download it from the nordic track website.

Posted on Mar 18, 2009

Ad

Anonymous

  • 64 Answers

SOURCE: Nordic Track Treadmill will not run

If console lights up but doesnt respond when buttons are pressed, you more than likely have a console problem. Key pad issue would be my best guess.

Posted on Jun 08, 2009

Anonymous

  • 103 Answers

SOURCE: Calibration Mode for nordic track treadmill model

Hello there, The calibration mode for a nordictrack is as follows.

With the safety key out, hold the stop and speed up arrow at the same time while inserting the key. Release the buttons. You will then be in diagnostics.
You then press the stop button one time.
If you are trying to calibrate the incline you just need to hit the incline up button and the machine will do an incline calibration. The unit should go all the way to the top and return to the bottom when completed.

If you need to calibrate the speed you will need to press and hold the speed up button on the console until the display reads 85. The machine should then be running at its maximum speed (either 10 or 12 mph depending on the unit)
The display will show a speed on the console and should be within .3 of the maximum speed.
If it is not then it will need to be adjusted using a potentiometer on the control pwb.
To access the control pwb open the hood cover. Should be 3 screws in the rear of the cover and 2 screws on the bottom of the unit.
Once inside the cover locate the control pwb. On the control pwb there will be a yellow/orange potentiometer. This is the adjusting part.
Use a non-metallic phillips head screw driver to adjust the potentiometer either clockwise for faster or counterclockwise for slower.
Hope this helps!
Good Luck! Tim

Posted on Jan 13, 2010

Testimonial: "Although I haven't attempted this solution, but it makes perfect sense and will attempt it as soon as I get back to the treadmill - Thank you"

Anonymous

  • 12 Answers

SOURCE: I have a Nordic Track EXP 1000X treadmill and the

Probably 85% of the time, it's the sensor.



1. remove the screws from the bottom of the enclosure case. 2 or 3 in the front and 1 on each side

lay it back down, and power it up, and actuate your incline. watch the end of the motor, to see if the shaft is moving. It probably IS turning but only a little bit. NOT enough. In this case I'd say it is the sensor.

2. Unplug the unit of course.
3. the incline motor is in the middle of the pack,..you'll see a black tube looking thing sticking up.
4. on the bottom side of this, you will see,..or feel for a black square sensor attached to bottom of the motor casing.
5. follow the wires and unplug this.
6. pry it off with a screw driver. Remove incline assembly, if you cannot reach it.
7. replace sensor and try it again.

if the MOTOR does NOT turn when using the incline buttons, the problem backs up to possibly a bad control board. or a bad motor on your incliner, however, i'd say that's the last thing to go.

Order of failure: 1. sensor 2. control board 3. motor.

good luck

Posted on Jan 26, 2010

Anonymous

  • 18 Answers

SOURCE: Nordic Track exp 2000I. Consol lights, buttons do not work.

If the console lights up but the buttons don't work, then unfortunately it's probably the console and they're not repairable that I know of. You may want to check the wiring harness and the connections at the console and at the controller under the motor hood. Pull them apart and check for bent pins. If they look good, the console is most likely bad.

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ordered vv20 portable 220 volt heater for my american home. question- will the heater work on my 220volt 60hertsystem with no damage to the heater. -heater came from great britain


If it says "100-240V, 50/60Hz", it will work anywhere with the correct plug.
Frequency ("cycles per second")is no problem usually as most things work on 50 or 60 Hz 60 Hz converts more easily to DC than 50 Hz , there's enough tolerance you can ignore frequency. Any clocks keeping time from frequency must have a sine wave.

Feb 28, 2014 | Computers & Internet

1 Answer

The remote control for my Zenith XBR413 is lost. Where can I find a replacement?


Model # IS 4070
AM/FM Stereo Receiver
With Phonograph and Cassette Play/Record
Serial # W288209
Power Source AC 120 V 60 Hz
78 Watts 0.65 Amps
Unswitched
AC 120V 60 Hz
200 W Max

Nov 05, 2012 | Zenith XBR413 DVD Player/Recorder and VCR...

1 Answer

I would like to know how many square feet a Model # BRCQ0421BD Serial # 990905429 Coleman Central Air Conditioning Unit will cover. The unit supply is 208-230V 1 PH 60 Hz 10.8 RLA 97 LRA.


The Old Rule of Thumb is 400 square feet per ton, but you really need to do a heat load calculation to be safe. A lot of windows on the west or south side of the house will really increase your load and you may need a lot larger unit. Insulation also changes your load so you may be able to cool a larger area. You may be able to get the Heat Load Calculation Form either online or from Johnstone supply. They are on the internet.

Aug 07, 2012 | Coleman Heating & Cooling

1 Answer

How can i change the power from 110 volt to 127 volt, jamaica is 110


Voltage is not the problem. The issue is a 60 hz machine in a 50 hz country. The fix is to buy a Jamaican washing machine.

Mar 03, 2012 | Daewoo DW500M Top Load Washer

1 Answer

I have an old zenith is4070. I am trying to figure out how many watts it pushes out to my speakers.


Model # IS 4070
AM/FM Stereo Receiver
With Phonograph and Cassette Play/Record
Serial # W288209
Power Source AC 120 V 60 Hz
78 Watts 0.65 Amps
Unswitched
AC 120V 60 Hz
200 W Max

Jul 09, 2011 | Zenith Audio Players & Recorders

1 Answer

Monitor CT-1050


This website has them for sale for $2.95. It's probably your best bet since it's so old.
http://www.smpcshop.com/TypeWriters-p-2-c-160.html

Dec 19, 2008 | Computers & Internet

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Cindy Wells

Level 3 Expert

6133 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Jesse Garza

Level 2 Expert

80 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...