Question about Cyberhome CH-DVD 300 DVD Player

1 Answer

Cyberhome DVD 300 player

I have had this player for almost 1 year but have played at most 5 DVD's on it. It was on standby and then the power light went off. And now nothing works. I checked the fuse inside and it was ok. Walmart would not honor the warenty. So I just sit it aside. Could not find any #'s to contact the manufacture. Any help appreciated.

Posted by Henry Wooden on

  • Henry Wooden Apr 12, 2007

    Toss it in the Dumster and buy something besides a Cyberhome from wal-mart.

  • Henry Wooden Apr 12, 2007

    Wal-mart would not honor waranty before it had been touched. Then I opened it up to check fuse. Power went through fuse and into unit but nothing worked.

×

Ad

1 Answer

Henry Thomas

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,074 Answers

Check the continuety of the power cord if its still good with no break, take the set to a tech for repairs the set has a problem in the power supply.however since walmart do not want to honor the warranty good luck.

Posted on Apr 12, 2007

  • Henry  Thomas
    Henry Thomas Apr 12, 2007

    walmart did not honor the warranty because you ad open the set and check the fuse.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Remote control for Cyberhome CH-DVD 300 is lost.

they are stop, eject, play ,ff, rr, pause, and power.
tip

Cyberhome CH dvd-300

Power supply problems. There are many reports on this site for problems related to the cyberhome dvd player, one of them mine. Here is what I found. The dvd drive was ok it was the power supply that failed after a power surge. The power supply is a flyback power supply using the viper22 switcher by STM Microelectronics. you can download the specs with a schematic diagram simular to the one in the cyberhome unit. I wound up replacing the shunt regulator (TL431) Optical coupler (PS2561-a-1) , the 2200uf cap and the 1000 uf cap. this brought the 5 volt output to 5 volts which was the problem. The parts can be ordered from Mouser Electronics.
1000uf @ 10 volts PN UHE1A102MPD
2200uf @ 25 volts PN UFW1E222MHD
TL431 PN 512-431CLP
PS2561 PN 551-PS2561-1-A

Warning: The high voltage side of this power supply has 120 VAC and 161 volts dc when energized. thak precautions when measuring the voltages on the output. Good luck

0helpful
1answer

My CyberHome DVD 300 says "bad disk" every time I load a dvd.

pls check ur dvd player optial pickup lense.try to clean or replace.
0helpful
1answer

Can't get my CyberHome CH-DVD 300 working

Check for bad capacitors on the alimentation fead target
0helpful
1answer

My Cyberhome CH-DVD-300 (dated 2003) will play movie DVDs, CDs with photos and music CDs. It will not play a DVD with a slideshow software for photos with music and text that I burn on my computer. The...

I feel for you because I also have the same unit and have been frustrated in the past when I tried different dvd's to play. The conclusion that I have come to is that I only use my cyberhome player to play rented dvd's
0helpful
1answer

I cannot get my Cyberhome DVD to work

Hello

I have a cyberhome dvd player CH- DVD 300 had it for a 1 year i but in a orginal dvd movie and it does play it it said no disc I but in dvd cleaner it read for a moment but when i put in the orginal movie it said no disc again is it the sensor or what, what should i do???
0helpful
2answers

DVD stopped playing all DVDs

Reset you player by doing the following:
With the player on, hooked properly to your television, and on the correct station:
Open the tray
Close the tray (with no DVD inserted)
Hold the stop button down for a full 5 seconds
The CyberHome screen should appear. You should be able to play your dvd's now.
0helpful
2answers

DVD problem

I have a cyberhome CH-300 my player running 50mins and next stuck the move .
1helpful
3answers

Cyberhome 300 DVD Player: pal to ntsc mode?

You might want to reset to factory defaults, but there is an error in the manual. In order to reset to factory defaults, turn on (with no disc inside), DO NOT OPEN THE DISC TRAY, just press the stop button on the player for 5 seconds.
Not finding what you are looking for?
Cyberhome CH-DVD 300 DVD Player Logo

Related Topics:

62 views

Ask a Question

Usually answered in minutes!

Top Cyberhome Televison & Video Experts

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

513 Answers

The Knight
The Knight

Level 3 Expert

76791 Answers

Are you a Cyberhome Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...