Question about Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

GU2400GTX Just installed new gu2400 and it started a cycle and now all it does now is flash the normal light, tried to do the diagnostic mode.Tried to unplug overnight to reset. nothing seems to work.any help would be great.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Novelist:

    An expert who has written 50 answers of more than 400 characters.
    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 148 Answers

Electronics fail most often when new. would not be surprised to see you have a logic board failure.
a new unit should not have any issue that would contribute to a malfunction, so looking for door switch problems or motor problems seems like a waste. call the service center for the unit.
good luck
mark

Posted on Dec 28, 2007

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won,t work just flashing blue light

Cycle light flashes, but machine wont start - Kenmore Elite ...

https://www.ifixit.com/.../Cycle+light+flashes,+but+machine+wont+...
iFixitThe Kenmore Elite HE3 is a washing machine by Kenmore. ... Whatever cycle I choose, the light just flashes and holding the start button ... I don't seem to have a black pin....the normal wash button just keeps flashing and won't let me start or .

The good ol' Whirlpool Lid Lock Flashing Light Problem - ApplianceBlog

www.applianceblog.com/.../42456-The-good-ol-Whirlpool-Lid-Lock-Fl...
Dec 11, 2013 - 10 posts - ‎3 authors Red Lid Lock light flashing intermittently when you try to start a cycle. ... Mode -- Lid Lock won't work, nor will anything that requires the lid to ... Once the lid has locked the second time, the washer ... shuts down with the lid lock blinking; go back into diagnostic codes and look for shifter or speed sensor errors ...

Nov 26, 2015 | Washing Machines

1 Answer

My F & P GWL10 Washer start it cycle and then stop after about 10 seconds and the green washer light flashes. I tried the diagnostic mode and it shows no lights or codes. Pat
Your lid magnetic reed switch is on its way out and needs replacing.

Aug 31, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

I have a Maytag Bravos xl dryer MED850WQ0 that won't start after power failure. Lights will come on, beeps are being made but it will not start. I have tried to go into diagnostic mode to see if
What happens in diagnostic mode?

Jun 16, 2013 | Dryers

1 Answer

Does my whirlpol du1145xtpb1 dishwasherr need to be reset
SERVICE DIAGNOSTICS CYCLE
To start the Service Diagnostics Cycle, press the
following keys, in order, in less than 6 seconds, while in standby(power on but unit off):
Heated Dry, Normal, Heated Dry, Normal
To Rapid advance one interval at a time, press the Start key, noting that
unlike Standard cycles, the Diagnostics Cycle automatically resumes
after door openings and does not require pressing Start to resume.

Once the diagnostic cycle has run and shut off, run a normal wash cycle, empty and with no detergent, to reset the control to factory "normal" operation. Make sure there's plenty of hot water.


Read more: http://forum.appliancepartspros.com/dishwasher-repair/261055-whirlpool-quiet-partner-ii-clean-light-flashing-have-reset-still-flashing.html#ixzz2UOcsE2Yg
http://forum.appliancepartspros.com

May 25, 2013 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

Whirpool dish washer model #Gu2400 -dishes are clean but clean light keeps flashing
Hi



Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...

When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light flashes 7 times, all buttons are non responsive). It does this as a safety in case the element is broken and feeding electrical current into the water.

To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring).
It rarely happens but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).



Please do rate the solution and revert for further assistance.


Thanks

Rylee

Oct 12, 2009 | Whirlpool Dishwashers

2 Answers

How do you reset the whirlpool gu2400 xtp83 dishwasher. the clean light is flashing. The unit will not start
Can be caused by detection of a heater circuit problem. You can reset by running the diagnostic cycle. To turn of the diagnostic cycle, press: HEATED DRY button, then NORMAL button, HEATED DRY button again, then NORMAL button. The cycle runsfor ~22 mins. When it completes, the blinking light should go out. You can then try running the dishwasher again. If the problem comes back, the heater element or Thermister may need to be replaced

Jul 29, 2009 | Whirlpool GU2455XTS Built-in Dishwasher

2 Answers

Kenmore Elite Dishwasher clean light ind flashing and won't start
You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 17, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

1 Answer

Clean light flashes
You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 11, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool gu2400 dishwasher
You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Dec 05, 2008 | Whirlpool 24 in. DU1055XTP Built-in...

1 Answer

Whirlpool gu2400 clean light is blinking 7 times
Yes this is a heater fault detection error. The unit may not be heating the water resulting in unsanitary dishes so the unit shuts down in this fault. Also the door may not have completely shut resulting in the heater not working, but everything else does (the heater common line is broken at the door switch. Clear the fault by entering diagnostics with this key dance heated dry, normal, heated dry, normal. All the leds will light, you can then press cancel and try another wash cycle. If fault occurs again, you must repair heater problem.

Dec 23, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?

View Most Popular

GU2400XTP Built-in Dishwasher

  • Dishwashers

Related Question

Won,t work just flashing blue light

  • Washing Machines

Open Questions:

0 Answers

Why is wash cycle flashing. Cannot turn off?

Oct 19, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

How old is dishwasher gu2400xtp

Jul 22, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

Dishwasher does not turn on

Jul 06, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

Light blinks and won't turn on

Jun 30, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

See all Whirlpool GU2400XTP Built-in Dishwasher Questions

Related Topics

Whirlpool GU2400XTP Built-in Dishwasher Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

26 Answers
Whirlpool Quiet Partner II

Whirlpool GU2400XTP Built-in...

4 Answers
Whirlpool dishwasher reset code

Whirlpool 24 in. GU3200XTP...

7 Answers
Whirlpool gold- quiet partner III

Whirlpool GU2400XTP Built-in...

12 Answers
WHIRLPOOL DISHWASHER, ERROR CODE 4,

Whirlpool Dishwashers

8 Answers
Whirlpool quiet partner III clean light blinking green

Whirlpool GU2400XTP Built-in...

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Bruce Denton

Level 2 Expert

273 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...