Question about Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Open Question

Fantom FM741B vacuum cleaner user manual - Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Posted by Anonymous on

Ad

5 Related Answers

defrankond

CJ C

  • 66 Answers

SOURCE: fantom fury vacuum

HOW DO I CHANGE THE BELT ON THE FANTOM® THUNDER® AND FURY®? a.gif fantombeltchange1.jpg
fantombeltchange2.jpg
fantombeltchange3.jpg

  1. Unplug the machine.
  2. From the front of the machine, remove the collection bin.
  3. Facing the back of your vacuum, remove each of the Philips head screws located above each of the rear wheels. (Figure 1)
  4. To remove the base cover, place your thumbs in the two screw holes in the back of the machine. Push forward and up on the screw holes to disengage the 3 cover locking tabs. Put the cover off to one side, and go to the front of the machine. (Figure 2)
  5. Check the drive arm for any black streaks which indicate residual rubber from the last belt. The drive arm is located on the right side of the motor. The easiest way to remove any residual rubber is with some nail polish remover on a rag or with steel wool.
  6. To attach a new belt, remove the brush from the base of the machine by pulling up straight up with two hands.
  7. Take the new belt and hook it over the steel drive arm. Pull back on the belt slightly, to create some tension.
  8. Put the brush inside the belt loop so that the track for the belt is aligned with the belt itself.
  9. Replace the brush by aligning the metal end so the points face downward. (Figure 3)
  10. Rotate the brush by hand to check that the belt is running freely and easily in its designated space between the bristle.
  11. Replace the cover by placing the nose in first. Once in place fasten with the two cover screws and then replace the collection bin.

Posted on Nov 30, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: Fantom Cyclone XT Vacuum Cleaner

FANTOM FURY VACUUM MOTOR CONNECTIONS. I REMOVED MOTOR TO CLEAN DEBRES FROM BLOWER.IT RUNS BUT SEEMS TOO LABOR.I MAY HAVE RECONNECTED WRONG

Posted on Mar 10, 2009

Ad

Alex

  • 97 Answers

SOURCE: Nedd power head wand for Fantom Model BPSRLC51

the best bet would be to look on ebay. the fantom line was discontinued

Posted on Jul 29, 2009

mc1bean

Mike Cairns

  • 3053 Answers

SOURCE: My Wife Purchased on TV

Hello, trumpet

I was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I would take some of my own personal time
to see if I can help. Even though this a Informational site may not have your exact model or brand, But this site will help you a lot. Here is the site link about everything you want to know about vacuum cleaners and possibly yours, from repair to trouble shooting it.

http://home.howstuffworks.com/vacuum-cleaner.htm


Please if this helped you at all, if you can find the time and in your heart to rate my help and some kind words written would be appreciated for my free help, I would appreciate it. Like I said I just tried to help, If anything this is good information for future problems. If you felt that my free help was a waist of time for you, I'm sorry.I do not get paid to help people on the site, I do it cause I like to help.

Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive, Appliance, and Electronics. Drop In anytime for my help.

Thanks, Mike


http://beta.fixya.com/users/mc1bean

Posted on Oct 30, 2011

awa13

AWA

  • 78 Answers

SOURCE: I need the two front

I have two for sale if you are still interested, and other parts for this vacuum. :)

Posted on Nov 16, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need an on/off switch for a Fantom Upright FM741B


Try these:

http://outdates.ecrater.com/

http://www.blujay.com/outdates

If no luck there, any power switch from another 120V product should work as long as the wires match. If you have a normal 2 wire switch, you should be fine. Be sure the amps on the new switch match the old and the terminals are the same size (don't try to force a small terminal onto a large one). Also, be sure that if you use another switch, be sure the terminals are wrapped or protected to keep them from shorting out if they were to fall off. With a little plastic modification, you sure can fit a square switch into a round hole lol. Good luck.

Nov 10, 2013 | Fantom Vacums Vacuums

1 Answer

I need an on/off switch for Fantom FM741B upright


Cathy, If I could see your machine I'd be more likely to be able to tell you whether or not you could get a switch or not. IF your machine is one of the older models then it's a good bet that there are no more switches available for them. I've heard that someone bought out the Fantom name and is now making them again. I think someone mentioned seeing an infomercial about them recently, but I can't be absolutely sure. If you take it to a reputable repair shop their mechanic may be able to find something that could work, but no promises.

Nov 10, 2013 | Vacuums

1 Answer

Euro-Pro Fantom FC-251 Canister Vacuum; Bought one of these 'gently used' at an auction. Would like a user manual if available.


You can download the manual by following the instructions on the following link. I used the security code to download it.

http://safemanuals.com/314159.php?k=4789186c8ac87e31888cf7e7294a3bd7&ID=347344&q=FANTOM FALCON FC251

Jan 08, 2011 | Euro-Pro Fantom FC-251 Canister Vacuum

1 Answer

I need a diagram of the agitator bar assembly on the FM741B. Please!


http://www.fantom.com/fantom/default.aspx
this site should do the trick

Nov 08, 2009 | Fantom Vacums FM760 Twister 500DX Bagless...

1 Answer

Nedd power head wand for Fantom Model BPSRLC51


the best bet would be to look on ebay. the fantom line was discontinued

Jul 28, 2009 | Fantom Vacums Lighting Canister Vacuum

1 Answer

New filter


TotalVac.com has parts for this model .Good Luck

Dec 06, 2008 | Fantom Vacums FM741 Twister Bagless...

2 Answers

Fantom Cyclone XT Vacuum Cleaner


Here is the owners manual which goes over some troubleshooting problems.

http://www.fantom.com/fantom/manuals/Cyclone.pdf

At first I would think it was the thermal overload, which is covered in the manual. But I would guess that you have let it sit for 30 minutes to cool down and tried again and the vacuum still didn't work.
I would think you may have one of four problems.
1. Your thermal overload was tripped and is stuck and will need replaced.
2. You have a clog in your vacuum lines or the brush roller is froze, which keeps causing the thermal overload to trip.
3. Your power cord has a short, which would need replaced.
4. Your power switch is bad, which would need replaced.
Out of these 4 possible problems I would say the only one you could fix on your own would be problem #2. Make sure the vacuum is unplugged and take the brush roller off and clean it, make sure it moves free. Check your vacuum lines to make sure you do not have a clog, other wise the motor does not get air flow to cool it down causing the thermal overload to trip. As for problem 1, 3, and 4 I would suggest taking it to a repair shop.
Hope this helps, post back.

Jul 11, 2008 | Fantom Vacums XT450K Upright Vacuum

3 Answers

Call Customer Service Call- 1-8O5-225-6690 We are Providing 24 Hour Support Service Number


Go to www.fantom.com. In Support Wizard, type in your model number. You'll see a file called Product Manual. click it to open and print.

May 22, 2008 | Fantom Vacums FM741 Twister Bagless...

Not finding what you are looking for?
Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum Logo

Related Topics:

122 views

Ask a Question

Usually answered in minutes!

Top Fantom Vacums Vacuums Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

ray gallant

Level 3 Expert

71369 Answers

Tom Chichester

Level 3 Expert

61666 Answers

Are you a Fantom Vacums Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...