Question about Heating & Cooling

1 Answer

E13 code, monitor 2400

I have a mpi monitor 2400, and the e13 code is always showing up. what does this mean? how do i fix it?

Posted by socold on

  • boatandfi359 Jan 17, 2009

    Did you ever get an answer.

  • Wade May 21, 2020

    So i had the E13 code come up on my 2400 i replaced the filter yes there was water but its to late buy that time put new filter in and bam E13 so i took the line off the burner( small copper line behind face plate) i turned it back on and waited till it started dripping dripping fuel after that i turned power off took ine off pump hooked it back to burner and blew through it hooked it all back up and turned it on fuxed it and put the face back on HOPE THIS HELPS

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

You have an obstruction in your fuel line. Lint or rust or some other debris, either in your main fuel filter which I hope you have or in the small one in the fuel sump on the lower right hand side (the little square hole below the round finger hole for the reset button). The screen is cleanable with air or brakekleen or both. Or it might be that your Constant Level Valve is tripping or has tripped. Push the button in the round hole on the lower right hand one time quickly (don't hold it down or press it several times slowly) and you should hear the float drop. Fuel should resume flowing to the fuel sump at that time.

Posted on Nov 03, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Solving e13 message on a mpi 2400 monitor


You have an obstruction in your fuel line. Lint or rust or some other debris, either in your main fuel filter which I hope you have or in the small one in the fuel sump on the lower right hand side (the little square hole below the round finger hole for the reset button). The screen is cleanable with air or brakekleen or both. Or it might be that your Constant Level Valve is tripping or has tripped. Push the button in the round hole on the lower right hand one time quickly (don't hold it down or press it several times slowly) and you should hear the float drop. Fuel should resume flowing to the fuel sump at that time.

Sep 26, 2018 | Heating & Cooling

1 Answer

Monitor MPI it flashes F 13 or 14 & smells, I had it cleaned 6 months ago


The codes are "E" Codes. an E13 is no fuel. E-14 means flame rod malfunction. Unplug the heater then reconnect, this will reset the heater. Try your red prime button. Could also be the fuel pump or your fuel source feed line isn't flowing fuel.

Feb 17, 2016 | Heating & Cooling

1 Answer

Monitor heater 2400 turned off with code E13, what does that mean?


This is an over heated indicator, what make and model unit.

Apr 04, 2015 | Heating & Cooling

1 Answer

How to fix a mpi 2400 with a e13 code how to fix


You need to have the system cleaned up.

Nov 18, 2014 | Heating & Cooling

1 Answer

E-14 code mpi monitor 2400


It sounds like you have a fuel problem, check to see if there is some kind of blockage in the line or at the tank value.

Jan 25, 2013 | Rinnai Toyostove Direct Vent Heater: Laser...

2 Answers

Monitor 2400 Kerosene heater service


Check your filter in the fuel line outside if you have one. Also check the strainer in the fuel sump.

Feb 02, 2010 | Heating & Cooling

1 Answer

E13 keeps blinking on my monitor 2400 heater


causes of E13 error code:
Failure of ignitor, solenoid pump
or circuit board.
Incorrect wiring or flame rod
touches to burner parts.
Air pressure switch or overheat
open

I recommend taking it to a qualified service center.

Unfortunately, this can be a hard problem to trace with some experience and equipment.

Hope that helps!

-Helping Hands Services-
_Fairbanks, Alaska_

Nov 21, 2009 | Heating & Cooling

12 Answers

Have a mpi monitor flashing a e13 code


I have a propane monitor heater just installed 2 months ago and I get an e 13 code and the heater won't stay on???

Oct 19, 2008 | Rinnai Toyostove Direct Vent Heater: Laser...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

5,200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3522 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18455 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...