I have a 795ft plus for 5 years.
I can't turn my monitor on. I have power because amber (orange) led is on. when I press the power the orange led blinking 4 times and goes off for 1 second and so on.I disconnect the signal cable but problem still remain.
I couldn't find any solution in troubleshooting guides.
what can I do now ?
if the problem related to the montor harware please describe the details. !
There is a step by step procedure
1.check the power cord. (try with a new one)
2.check the monitor on other pc, even if it is not working on the other pc, then carry to a service centre.
3.if it is working on the other pc then check the vga slot/card of your pc then
4.try to change the vga card and try connect an other monitor to your pc. so basing on this you will be able to trace the problem.
5.still the problem persists the consult the service centre.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Switching the power
1 Auto) Far left of the 5 buttons on the bottom
2/3 ) On the right
Minus / Plus
4 OSD functions) Second from left
5) Power: the middle button
Adjusting display settings
If the OSD is active, press Auto to exit a selection in the OSD. If the OSD is
inactive, press Auto and the monitor will automatically optimize the
position, focus, and clock of your display.
If the OSD is active, press Minus or Plus to toggle between the OSD
options. If OSD is inactive, press Minus or Plus to adjust the volume.
Press to view the OSD. Press again to enter a selection in the OSD.
Green: power on
Orange: in sleep mode
If the led does not light up at all then either the power lead is faulty or there is no power in the power board.
Interesting, sound like a failure of the button because most system either work with a greeg lit up led or fail with an amber or orange lit or flashing. In this instance the amber could mean something has gone bad but the fact you can hold the button and have it boot up is strange.
Does the led turn green after holding the button for a while to let the machine boot?
please try to remove and plug VGA cable back again to the monitor. and press the menu button in front of monitor if it doesn't giving any message in monitor it means that the control card inside the monitor is faulty.for fixing that you have to contact your local service center.
1. Verify AC power presence with MagSafe LED
indicating on or charge state.
2. Verify battery as being partly charged, with
orange/amber LED on MagSafe power connector.
3. Reset SMC
Resetting the System Management Controller (SMC)
The System Management Controller (SMC) is a chip on the logic board that controls all power
functions. If the computer is experiencing any power issue, such as not starting up, not
displaying video, sleep issues, or fan noise issues, resetting SMC may resolve it. To reset SMC:
1. If computer is on, turn it off by choosing Shut Down from the Apple menu.
2. Connect power adapter to computer and to a working power source.
3. On built-in keyboard, press (left-side) Shift-Control-Option along with power button just
once. Important: Use Shift-Control-Option keys on left side of keyboard.
Note: When the LED on the MagSafe connector is orange/amber, resetting the SMC will
change it to green for a few seconds, indicating that SMC was correctly reset.
4. Wait 5 seconds and press power button to start computer. Note: If bottom case is removed,
you can alternately reset SMC by disconnecting both power adapter and main battery, and
holding down power button for 5 seconds.
Power Adapter Issues
1. Connect AC adapter's MagSafe connector to the
computer. The LED on the connector should be
green or orange/amber.
2. Verify power cord or duckhead is firmly attached
to AC adapter. Check that duckhead is not
3. Verify AC power source is supplying AC power.
4. Check for dirty or stuck pins on the MagSafe
connectors, both on the adapter and the
5. Reset SMC by pressing the (left) Shift-ControlOption(Alt) keys along with the power button
Step 1: Manual Temporary 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green. 6. Release both buttons.
step 2 : Software for Permanant 1. Reconnect the printer cable. 2.Open General Tools software and select (USB PORT) 3.Choose (SET DESTINATION 1) And it should be reset. Sofware Download "After service mode Pls use software for permanent reset Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
1. Hold down RESUME and then hold down POWER 2. Release RESUME 3. Press RESUME twice, then release POWER 4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute: presses - light color - function
Number of presses - light color - function 0 presses - green - Test print (or exit service mode on i960) 1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i850) 2 presses - green - EEPROM initialize 3 presses - orange - Reset waste ink counter
With the printer plugged in and powered off, press and hold the Resume/Cancel button, then press and hold the Power button. Do not release the buttons. The LED light should be green to indicate that a function is selectable
While holding the Power button, release the Resume/Cancel button, do not release the Power button
While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.
When the LED light is green, press the Resume/Cancel button 4 times. Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.
Press the Power button. The LED lights in green, and the reset is performed. When the operation completes, the printer returns to the menu selection mode automatically
YOU NEED TO CHECK TO SEE IF THE CAPASITORS ON THE POWER SUPPLY AND MAKE SURE THERE NNOT BULGED OUT OF LEAKING IF THEY ARE THE NEED TO BE REPLACED
YOU SHOULD BE ABLE TO FIND EVERYTHING YOU NEED AT RADIO SHACK FOR LESS THEN 20 BUCKS
it could be th epower supply and it could be the monitor.
power ON button should not flash orange regardless what you do. it should stay green. then orange. not orange to green to orange.
try the monitor on another PC if you can fine one.
the other thing is are the 2 monitor similar (CRT to CRT and LCD to LCD), you can't mix the the two, they will work but need different video driver to function correctly.