ILO TV I AM HAVING PROBLEMS WITH THE COLOR. THE PICTURE IS GREEN OR IT HAS A GREEN TINT. HOW DO I GET THE PROPER COLORING BACK? THANKS, DIANA FERNANDEZ

Adjust the tint, contrast and color settings on the TV remote control to determine if these changes solve the problem.
Read more: How to Troubleshoot a TV With Green Picture Problems ' eHow.com http://www.ehow.com/how_5387115_troubleshoot-tv-green-picture-problems.html#ixzz1goh6jjyV

Pictures still have colors shadows mixed into the tv picture wright?Yes?Tv still have and causes by convergence board as a problems.

i think is the blue mirror in side the tv...it has 4 mirrors inside

The color signal consists of Red, Green and Blue. Those three colors, at various degrees, make all the other colors on your screen.

If you have a BRIGHT green screen it's best you don't operate your set.
If it's just tinted green then there is a problem on the CRT (Cathode Ray Tube) drive board. Do check your "tint" setting and see if someone misadjusted it. If that isn't it then you need to have your set on an electronics bench and get an estimate for repair.

I think I have a solution involving far less effort. Have you tuned your picture settings? Out of the box, the settings are ok and the presets will do the trick for most. But if you're like myself, you want the best picture possible. Here are my settings:

Picture menu:
Aspect ratio: Just Size
Energy Saving: Off
Picture Mode: Expert 2
Backlight: 35
Contrast: 90
Brightness: 54
H Sharpness: 40
V Sharpness: 42
Color: 50
Tint: 0

--Expert control menu
Dynamic contrast: Off
Noise reduction: Off
Gamma: Medium
Black level: Low
Real Cinema: On [grayed out]
Color Standard: HD [grayed out]
Color Gamut: Standard
Edge Enhancer: Off
xvYCC: Auto [grayed out]
OPC: Off
Expert Pattern: Off[grayed out]
Color Filter: Off

White balance: Warm
Method: 10 point IRE
Pattern: Outer
IRE: [see below]
Luminance: 137

-- 10 point IRE calibration
IRE: [Red, Green, Blue results, respectively, for each IRE point]
100 [-8, 1, -40]
90 [-13, -5, -40]
80 [-20, -12, -40]
70 [-17, -14, -33]
60 [-17, -12, -31]
50 [-17, -13, -26]
40 [-13, -12, -19]
30 [-6, -4, -8]
20 [-6, -4, -10]
10 [2, 3, -1]

Color management system
Red color: 2
Red tint: 0
Green color: -1
Green tint: -7
Blue color: 2
Blue tint: 7
Yellow color: 0
Yellow tint: 1
Cyan color: 0
Cyan tint: 0
Magenta color: 0
Magenta tint: -2

These are taken from CNET.com

I have a good but with green tint on a polaroid tv model number 64SX505Y-DC02

Picture Menu
Picture Mode: Expert1
*Backlight: 16
*Contrast: 83
*Brightness: 53
Sharpness: 50
*Color: 55
*Tint: 0
Expert Control

• Fresh Contrast: Off
• Noise Reduction: Medium
• Gamma: Medium
• Black Level: Low
• Real Cinema: On
• TruMotion: Low
• Color Standard: HD (N/A w/HDMI)
• White Balance: Warm
• **Method: 10-Point IRE
  • 10 IRE
    • **Red: 1
    • **Green: 2
    • **Blue: -16
  • 20 IRE
    • **Red: -6
    • **Green: 0
    • **Blue: -7
  • 30 IRE
    • **Red: -5
    • **Green: 0
    • **Blue: -4
  • 40 IRE
    • **Red: -8
    • **Green: 0
    • **Blue: -4
  • 50 IRE
    • **Red: -4
    • **Green: 4
    • **Blue: -4
  • 60 IRE
    • **Red: -6
    • **Green: 6
    • **Blue: -5
  • 70 IRE
    • **Red: -8
    • **Green: 3
    • **Blue: -10
  • 80 IRE
    • **Red: -8
    • **Green: 7
    • **Blue: -16
  • 90 IRE
    • **Red: -9
    • **Green: 5
    • **Blue: -18
  • 100 IRE
    • **Red: -10
    • **Green: 4
    • **Blue: -9

Color Management System

• Red Color: 0
• Red Tint: 0
• Green Color: 0
• Green Tint: -15
• Blue Color: 0
• Blue Tint: 11
• Yellow Color: 15
• Yellow Tint: 2
• Cyan Color: -15
• Cyan Tint: 0
• Magenta Color: 0
• Magenta Tint: -1

lg70 nice tv excellent processor just to bad there is no intensity control on color management oh well still better than what the three s are pushing block out the hype lg will be number 1 in a few years haters are starting to come around and well leds coming,

p.s. i dont work for lg just tired of losers bashing stuff because they dont own it.
im isf certified those settings are right on the money straighter than a ruler

Colorimetre HCFR software
AVC HD 709 calibration disk
Spyder2 colorimeter (I know most prefer the Eye-One meters, but the Spyder2 was available from my job at no cost)

Here are the settings:

PS3 Blu-Ray player

Output Format (HDMI): Y Pb/Cb Pr/Cr (important!!! NOT RGB output)
BD 1080p 24hz Output (HDMI): On (this TV can reproduce video at 48hz for accurate 2:2 pulldown)
Y Pb/Cb Pr/Cr Super White (HDMI): On (not sure if this matters)

42LG50 Settings

Aspect Ratio: Set By Program (Personal Preference)
Picture Mode: Expert 1
Backlight: 50 (Personal Preference)
Contrast: 54
Brightness: 54
Sharpness: 40 (Personal Preference)
Color: 50
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 10 Point IRE

10 (-3,8,-16)
20 (15,24,-21)
30 (20,36,-22)
40 (3,19,-40)
50 (8,34,-41)
60 (10,50,-20)
70 (-5,50,-8)
80 (-16,50,18
90 (-14,50,30)
100 (-22,38,21)

Red Color: -3
Red Tint: 0
Green Color: 10
Green Tint: 0
Blue Color: 14
Blue Tint: 0
Yellow Color: 0
Yellow Tint: 1
Cyan Color: -11
Cyan Tint: 0
Magenta Color: 0
Magenta Tint: -2

Take time to get used to the settings, you may think the screen looks dull at first. The truth is most people have way too much contrast on their TVs.
These settings will also work for Cable or Dish hookups, in which case you may change the Noise Reduction option to Medium to reduce signal noise.

OR....

2POINT IRE

Backlight: 65
Contrast: 55
Brightness: 45
Sharpness: 50
Color: 45
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 2 Point

Red Color: 3
Red Tint: 0
Green Color: 9
Green Tint: 2
Blue Color: -1
Blue Tint: 0
Yellow Color: 6
Yellow Tint: 5
Cyan Color: -1
Cyan Tint: 1
Magenta Color: 2
Magenta Tint: -1

if you have hd cable or satellite box make sure the component cables are properly connected(green red and blue) and matching same color in source (cable box or satellite and tv as well)
also make sure in tv menu that color and tint are 50%

Hopefully someone on here has a manual and can tell you exactly where the tint controls are. Also need to try adjusting the color level, turn it clear down so you have a black and white picture.
Is the picture still green over the screen with the color control
set clear down to black and white? If it does, you might
have an issue with the green gun going out or problem in the
circuitry to it.


By the way, the best way to adjust the picture settings on a
tv are to first turn the color control clear down, then adjust
brightness and contrast for best black and white picture, then
bring up the color level to where it should be and adjust the
tint for best red/green ratio.