Question about Kenmore 23822 Top Load Washer

Kenmore catalyst SM 9710768-D

My Catalyst is flashing OL on the front screen. It fills with water but does not aggetate. Please Help!!! Cuervodefender

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

Mayor:

An expert whose answer got voted for 2 times.

Problem Solver:

An expert who has answered 5 questions.
Contributor
5 Answers

Pls check lid switch operation

Posted on Aug 16, 2007

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Whirlpool cabrio model 6300sw1 won't aggitate and gives ol code

It is overload error.
"oL" (Over Load)
Is the washer overloaded? The washer has attempted to fill •
and begin the wash cycle. If the washer is overloaded, it will
drain any water and detergent that was added during the fill.
To correct the overload, remove several items and add
detergent. Close lid and press START.

Also try to download user manual from this site and check page 19.

Download WHIRLPOOL CABRIO WTW6300SW1 Use Care Manual

Sep 03, 2014 | Whirlpool Washing Machines

2 Answers

Screen say OL on my Kenmore Catalyst Elite. What does oL mean?

OL error means the Motor Controller has sensed an Overload.

The oL code means the motor control board is struggling to power the motor up. If it recurs after removing some clothes - usually this means a new motor control.... or worse - a new bearing.

If it were a problem with the tub floating up, the unit would spin instead of nutate.

Bearing failure in this machine is very common.

I suspect the drive shaft and bearing are the problem. The bearing and shaft are part of the outer tub.

Feb 28, 2013 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

The oL warning comes on, just after the machine fills with water then it clicks through the cycles the water drains and the oL signal comes on. This even happenens when the clean cycle is operating.

oL Overloaded.
"oL" flashes when you got too dang many clothes in there. 18 pounds dry weight per load is what I go by. If the load is fine you could have an item of clothing in between tubs not allowing basket to engage.

Service Manual and codes HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jun 20, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

2 Answers

IN THE WASH CYCLE THE TUB FILLS ALMOST TO THE TOP THE DRAINS. THE OL CODE THE APPEARS AT THE END OF THE CYCLE

Hi, the OL code means Overloaded..
OL flashes when the machine/motor control detects a load size that exceeds the washer's capacity.Open the door lid to clear display, remove excess laundry, then restart the cycle.

Oct 04, 2010 | Whirlpool WTW6400SW Cabrio Washer

1 Answer

My machine is not aggetating it just keeps filling with water

if the water is not over flowing on the floor.make sure your washer is off,then pull the drain hose up to the level of the back control panel you should here water flowing out once this stops.keep the hose up for aminute and restart your waher and it should fill up to the proper level and shut off and start washing

Sep 26, 2009 | Maytag Legacy Series Top Load Washer

1 Answer

I have an older (about 1998) Whirlpool washer. After the aggetation cycle the machine fails to drain. We can back up the cycle to aggetate and begins aggetate again. It again fails when it gets to the...

You quite possibly have a small article of clothing such as a sock, that may have been washed over the top of the inner tub and is in the outer tub and blocking the drain hose to the pump.
If you can remove the front cover, you can check to see if the pump is clear and also the belts underneath.
If it appears to have something in the pump you can pull the hose (be prepared for alot of water) and pull it out of the pump.
If it is in the outer tub, you can fish out the blockage with a straighten coat hanger wire with a small hook bent on one end.
Let me know if you have success...
k

Jul 09, 2009 | Washing Machines

1 Answer