When Istrted to wash my cloths , the washer stop and post F-20

Washer Repair - Not Advancing -Repair & Diagnostic ...

? 8:30
https://www.youtube.com/watch?v=IEr9A7uhdN8
Sep 6, 2013 - Uploaded by ApplianceVideo.com
Repair your Kenmore Top Load Washer suffering from these following issues: Will Not Advance Past Rinse ...

Kenmore washer doesn't complete final spin cycle - ApplianceBlog

www.applianceblog.com/.../31894-Kenmore-washer-doesn-t-complete-fi...
May 16, 2012 - 9 posts - ‎2 authors hello, my kenmore washer doesn't complete the final spin cycle. i ... Does it stop in the middle of the final spin cycle or does it not go into the ... FIXED Kenmore Washer - Not finishing the spin cycle
9 posts
Dec 20, 2014
FIXED Washing Machine Does Not Complete Cycle ...
10 posts
Mar 14, 2013
FIXED Kenmore washer won't spin out all water from ...
10 posts
Jun 27, 2009
FIXED GE front load washer WCVH6260F0WW stops ...
10 posts
Jul 2, 2007
More results from www.applianceblog.com

Check the washer drain hose for clogs.

First you need to open the cabinet and remove the boot from the tub to the pump and clear the filter. Try that then run a cycle and post back the results.

Under the lid there should be a small hole with a push down flap and that should be the automatic stop, which can either be a bad switch under the top of the machine or could be a broken trip/ prong on the lid that pushes this button when the lid is dropped. When the machine reaches it's spin cycle time leave it turned on and raise the lid push down on this flap with something careful to keep hands out of the washers tub and see if it works then!

The code is UE

load too small.
• Load is out of balance.
• The washer has an imbalance
detection and correction
system. If individual heavy
articles are loaded (bath
mat, bath robe, etc.) and the
imbalance is too great, the
washer will make several
attempts to restart the spin
cycle. If an imbalance is still
detected, the washer will stop
and the error code will be
displayed.
• Add 1 or 2 similar items to help balance the load.
• Rearrange items to help balance the load.


please rate this help to keep the service online

If it’s an FAV6800A I think you may have a clutch malfunction with your machine. To verify if the clutch has malfunctioned we need to perform a quick check. Please visit this link and review my post of Solution #1 posted on Jan 30, 2009. Steps 1 & 2 should get you started and give us some troubleshooting direction. Please post back with your results or if you have any questions.

http://www.fixya.com/support/t1612027-maytag_neptune_fav6800aww_wont_spin

Good Luck… Rich.

Dear shelldon39, Fri 2-20-2009 9:24pm EST (USA)

Some machines will shut down during the spin cycle as a precaution to prevent damage!

They will do this if you overload the washer with clothes and/or use too much detergent!

If this doesn't help please get back to me with more details!

jack

Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know

remove bottom cover and clean pump

If this is a Whirlpool, Estate, Roper, or Kenmore model Top Loader, the problem is a lid switch malfunction. This is the most common symptom when the lid switch fails. The washer will either fill normally, then stop. Or, it will fill, agitate, then when it gets to the spin cycle, it will stop. If these match the symptoms you are experiencing, please post back and let me know. I can assist you and explain how to repair this problem. This is an inexpensive repair that anyone can accomplish with a little guidance. I have step-by-step instructions posted under the "Tips and Tricks" section of my profile.

Please provide as much information as possible when posting questions, as all washers are not alike and symptoms differ between models. This makes it much easier for us to provide you with the proper diagnosis. Let me know if you need my assistance.

PS You do not need to drain the wash tub to repalce a defective lid switch. The washer will drain on its own if the switch is replaced. In the interim, I can also give you advice on how to by-pass the lid switch as a temporary means of draining the washer.