Kenmore 98702 Stacked Washer/Dryer Logo

Question about Kenmore 98702 Stacked Washer/Dryer

2 Answers

Kenmore stackable I have a kenmore stackable model:110.98575120 s/n:ME3308533. It does not aggitate or spin and the tub leans to the left side.I have done nothing to fix it except internet searches.I will attempt to fix it but wanted to get some more info, if it was even worth it. The dryer also spins but does not heat!!

Posted by James Wigglesworth on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Washer issue is lid switch. need new one. dryer sounds like either the main breaker to unit (only 110v passing thru to dryer instead of 220...then spin with no heat will occur), the heating element is bad or a thermal switch got hot and failed (cheap to replace). There is not much to a dryer, and that covers all the possibilities.

Posted on Sep 06, 2009

Ad

Ian

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 51 Answers

Dryer probably element or thermostat, washer sounds like a suspension arm collapsed. Price up the parts & then decide if its worth it! Regards

Posted on Jul 25, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Kenmore top load washer,model 110 20102311,should i be able to move tub from top very easily in any direction or should there be some tension,my tub is banging of side walls in spin cycle

The tub should move easily from side to side, however, a better test is to push down sharply on the tub and let go, it should come up and stop the first time, not bounce up and down several times. If it bounces up and down the suspension rods are shot. The part number for the kit of 4 is W10780045, all 4 need to be replaced as a set. To replace them the top needs to be loosened and lifted up, the rods disconnected from the top 2 at a time and replaced (doing opposite corners makes it easier IE: front right and left rear, front left and then right rear). Disconnect the top ends of two rods, lower top, lean washer back and pull out the disconnected two rods from the bottom, reverse the process to install.
0helpful
1answer

Stackable kenmore washer dryer

could be a clogged pump or drain hose causing the water to spin over the top
0helpful
1answer

I have a top loading Kenmore Washer - Model # 110.92588210. When it spins, it sounds like its going to knock the sides off. Also, the tub inside leans to the right - when empty and when full. Can...

The skate plate must line up with the base, if it is off then the washer will lean to the right or left. The washer has 4 springs under it. 3 that connect to the tub and one in the rear from tub to base:
themobilian_2929.jpgthemobilian_61.gifthemobilian_2928.jpg

Video: How to tear it all the way down and look

Service manual and more are here

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61


0helpful
1answer

Just purchased used a Kenmore stacked washer/dryer: tub spins during aggitation cycle. So my clothes are spinning around in water but not being aggitated. Now Im aggitated!! Grr!! How much will it cost...

Sounds like the plastic spacer between the transmission and the tub has broke. Part is no more than 5-10 bucks. Labor, not sure. Did you buy the warranty....I think you still have time to buy it if it's new... But I think Kenmore may guarantee for 30 days but you may want to call where you bought it from new.
0helpful
1answer

Kenmore stackable #85751 tub seems broken

if it is leaning to one side then it most likely needs spring kit, like shocks on a car
0helpful
1answer

Water under stackable washer dryer

The front panel comes off and you will be able to trace the water source. These combo units spin immediatly and if the drain is slow the water will spin up over the edge of the tub during drain.
Eric
0helpful
1answer

My Kenmore model 110 will hum, but the agitator does not turn.

If the motor is running and it is not aggitating or spinning than u have a bad coupling. lean the machine back and look where the motor mounts to the transmission. look to see if you have a broken coupling connecting the two together.
0helpful
1answer

Water drains during spin cycle, but tub does not spin and appears to have dropped down. Machine does aggitate.

If you can move the tub by hand laterally - the rear main bearing has likely failed - or the drum rollers are worn.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
0helpful
1answer

Washer won't drain or spin

sounds as if you have a lid lick/door switch issue, the machine is not recognizing the door being closed and for safety reasons will not enter spin/drain.. open anc\d close lid a few times slowly, cam you hear a "clicking noise" whe njust about closed?? id assume not replace teh lidswitch
0helpful
1answer

Kenmore model # 110.20722990

ck all motor connections just lean washer back against wall motor is right at front if motor ckd ok 2 things left motor or timer neither one is cheap but best guess would be timer
Not finding what you are looking for?

665 views

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Cindy Wells

Level 3 Expert

6448 Answers

tina gallow

Level 2 Expert

143 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...