GE JBP24 QuickClean Electric Kitchen Range Logo

Related Topics:

Question about GE JBP24 QuickClean Electric Kitchen Range

1 Answer

My indicator lights have "slid" out of sight

My oven works perfectly, however the burner indicator lights cannot be seen anymore unless you look at them sideways, in line with the counter. They have gradually slid to the right. Is there a way to slide them back over so that they are in sight again? Thanks!

Posted by Kristin Minor on


1 Answer

Archie Ferrarini

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 869 Answers

You have to pull the top cover up and re-set the position and you are good to go.

Posted on Jun 01, 2008


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


How do we start the Oven?

first question
have you turned the gas supply on?

Top burners work, but oven and broiler won't come on and control panel won't light up.

I need the make/model number to help you accurately. However, from what you're describing, it sounds like the oven control board is blown out. The oven is totally separate from the top burners on a lot of units. You will have a separate burner control knob and then a panel for all the oven controls. The fact that the top burners work indicates 240v is getting into the range. Did you have a power outage recently? Usually about 3-4 weeks after the event things happen or *don't* happen with electronic appliances. This is because surge-damaged chips start to fail after a period of time if the unit wasn't blown out immediately by the power restoration. When the power company restores power, there is usually a large surge of current and it overwhelms the computer boards in microwaves, ovens, dishwashers, washers, dryers, refrigerators, etc. Also, I've seen bug infestations where the board is blown out due to the critters crawling across the live boards--if the clock is on, there is power on that board. I hope I helped you!

We recently moved, when we got to our new house we plugged in our stove. We turned on the burner and it didnt work, we tried the other three and they didnt work either.. Finally we tried the oven but there...

i would first try the breaker it sounds like you only have half the power coming to unit and the light and clock will work but the heating componets will not as they require the full 220-245 volts
it sounds very odd that everything as far as burners and elements are out but you have a clock display and light... you have lost one of the legs of power somehow...either the double breaker is not fully on and may require turning off oven breaker and resetting or half the breaker has failed... a sure way of testing would be to pull out and with a volt meter test to see that you have 220-245 volts coming to oven,,, hope this helps out repost if anymore questions...

Ancient (1971) Frigidaire Cookmaster electric Compact 30 Range/Oven, model number RBG-533N, has two surface mounted red indicator lamps; one for the oven & one for the burners. The surface burner...

The stove has 4 burner switches with a # 2 terminal on each switch. This contact is similiar on all four switches. One of the switches # 2 contact is stuck. The burner switch should disconnect both legs of the 240 volt circuit, one leg through the # 2 terminal and one leg through the thermostat built into the burner switch. Disconnect the pilot lamp wire on each switch unti the light goes off and then replace that burner switch. This should correct the problem

[email protected]

Range indicator light doesn't shut off

the poles for the light are reversed or miswired
at the selector switch
make sure the light goes back to p1 or p depending on your switch

Burners not comming on

Remove the grill and slide out the glass top. Take a close look at them burner. If all look ok then it may be the switches.

If you need further help, reach me via phone at


Viking range burners won't light

All of these ranges have a spark module at each burner sight and they all click when ever you attempt to light one burner. Therefore, it can not be assummed that the spark module for those nonworking burners are actually clicking. Remove the burner covers and actually look for the sparks. If there is no spark make sure the connections are nice and tight. IF they are, you most likely need to replace the spark module.

Oven and lights stopped working

is it the indicator lights at the top or just everything in the oven that is not working??

If it is just the light in the oven and the oven not heating then you are having a problem with your control board.
Not finding what you are looking for?


Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Ismael Rodriguez...

Level 2 Expert

188 Answers

Cindy Wells

Level 3 Expert

6450 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides