Question about Kodak EasyShare C340 Digital Camera

1 Answer

No power when you try to put it on there is no power

Posted by wayne richards on

  • wayne richards Mar 18, 2007

    I tried recharging the rechargeable batteries, but that did not solve the problem. I then installed new batteries and that did not solve it either.

  • wayne richards Mar 19, 2007

    Can you provide me with the cost of the new board?

×

Ad

1 Answer

CameraFix.com

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 154 Answers

This camera has one main board that controls evey functions. To remedy the problem, you need to replace the main board. Kodak may have good flat rate for repair or replacement unless you want to upgrade to newer models for few more dollars. Good luck.

Posted on Mar 18, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Load disc, unit tries to load & play, unit shuts off. Turn power on to set time,etc,machine shuts off.

Laser pickup unit fault. The unit alongwith its flat connecting cable should be replaced. Contact any service technician. Electro help
0helpful
1answer

I had absolutely no power and I couldn't even jump

No Power? Do you mean that the engine would not crank when you turned the key? Did you have dash lights? Dome lights? If you had some kind of lighting, you had electrical power. and if that is so then it sounds like your transmission range selector switch may be faulty or needs adjustment. Or VERY POSSIBLY, you might not have put it ALL the way in Park when you turned the car off the last time. If you try it now does it start? If not try putting it into park a little harder. Does that work? If not put in Neutral and try it. If that works the Gear selector switch Is bad or in need of adjustment.
1helpful
1answer

I have an XM600 that will not power up. The light on the power button lights up in amber. I have replaced the power supply with the same results. The PC worked and I gave it t my niece. When she put it...

Take out the CMOS battery for two hours. Also, try to power it up without the CMOS battery. This will clear CMOS. Then put the battery back in and try again. Also, try reseating ALL cables, memory, ect....
0helpful
1answer

Last fre days i didn;t use my laptop. today i tried to put on. it is not swich on. no lights. what ahppend plz help

Remove the battery, remove the power plug, press the power button for 5 seconds. Plug the machine back in but do not put in the battery, try to power the machine on.
1helpful
1answer

I just put a new 9 cell battery, two new 2GB ram cards & a new, blank hard drive in our Dell Inspiron 1525. But the screen does not seem to work when I turn it on, or after I put in an installation...

Remove the battery, and connect the AC power. Then, try to start it.

Disconnect the AC power, and remove the "new" disk-drive.
Then, connect the AC power, and try to start it.

Disconnect the AC power. Remove the "new" RAM, and put the "old" RAM back in.
Then, connect the AC power, and try to start it.

If it does start, add the "new" disk-drive, and try again.

If it does start, add the "new" RAM, and try again.
0helpful
1answer

My toshiba satellite 2545 cds will not power up. the power supply cord works I have checked that. but I push and/or hold the on/off button...nothing. ideas?

Try this for me;

Take out the power cord;

Take out the adapter;

Hold power button for 30 seconds

Plug power cord back in;

Put batter back in;

and try to power it up again..

If the adapter is working (and you are sure of this?) your battery may be dead.

Also; try using JUST the adapter to turn it on after you repeat the steps above without putting the battery in.

Good luck;

We will go from there if this doesn't help you!

KittyTech

If you need further help, reach me via phone at https://www.6ya.com/expert/carolyn_427ff26936286336

0helpful
1answer

No power totally dead

Try putting your device in a bag of uncooked rice. Put it in there for 6-12 hours. Your problem should be fixed
0helpful
1answer

My amp protection will not turn off i tryed almost everything?

i wish i can chat to you live so i can ask you qestions about your amp but to figure out what section of the amp might be fried it could be the power supply section could be the out put section or the in put section but i would try process of elimulation try unplugging your rca jacks and your subs unhook to your amp just the power hook up and try powering it but if the protection light steel comes on then try to remeber the last time your amp was working good and playing your subs was your amp getting hot if so you probaly fried your out put chips and not telling what else next question was you just hooking your amp up in your car and acually touch one of the power wire to the ground on your amp this happen to my friend and fried the power circuit relay chip on the power supply thats all the advice i can give but usually when the protection light comes on and you got every thing hook up right something fried
0helpful
1answer

Lap top freeze when trying to put it off.

are you replacing the battery properly and does it come on with
AC power jack
2helpful
2answers

Putting out half the volts

My 13 hp 8000 watt is not putting out any power dose it need to be exsited and if so were do i do it at?
Not finding what you are looking for?
Kodak EasyShare C340 Digital Camera Logo

Related Topics:

55 views

Ask a Question

Usually answered in minutes!

Top Kodak Cameras Experts

Ekse

Level 3 Expert

13435 Answers

Cindy Wells

Level 3 Expert

6302 Answers

Brad Brown

Level 3 Expert

18726 Answers

Are you a Kodak Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...