Mag Innovision lt456s 14" Flat Panel LCD Monitor Logo

Question about Mag Innovision lt456s 14" Flat Panel LCD Monitor

2 Answers

MAG Innovision LT456s monitor power issue.

I have been given a MAG Innovision LT456s monitor without a 12v power adapter. No problem, as I have plenty of 12v adapters from my collection. Only problem I can't find a place to plug it in? Help?!? I would appreciate any assistance as I haven't found any online yet. Thanks. Wade

Posted by Wade Pena on

  • Wade Pena Mar 20, 2007

    Hi all, Wade here. Thanks for the assistance, but I found it! As it turns out the 12V plugs directly into the monitor lead that plugs directly into the computer!? Very odd, but functional. Thanks again.


  • monkeymen22 Mar 22, 2009

    How and where?



2 Answers


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 944 Answers

If you ask them nicely they just might tell you, else it's only $5 for a user manual(sorry no luck online); this link has a picture that maybe shows a power cable going to the bottom right (as you look at it) but it's hard to be sure; this link shows what the power lead should be like - look for a hole that matches; Hope this helps, if not ask again :)

Posted on Mar 17, 2007

  • Anonymous Jul 28, 2011

    keep up the good work (c&p solutions?). I figure someday I'll be a ultra-guru, just by answering wrong a few million times. right or wrong?




  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Must have 12V, >2A, laptop-type adapter plugged into back of VGA plug.

Posted on Jul 28, 2011


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


I am unable to get MAG Innovision 14" LCD monitor

You need laptop-type 12V, 2.5A (minimum) adapter plugged into back of VGA plug

I need a driver i think for my mag lt456s monitor i hook it up to computer and i get no power or anything

first check the power cable connection at both end i.e. source of power and also at monitor side if loosen one tight it or may try to change the cable

A Simple Power Adaptor Issue

see are u sure that cable is for that slot...
try to open it as slider or use some lever to open it

I need a power cord for a mag innovision lcd monitor

You can buy a power cord at any Lowes, Home Depot, Radio Shack or Best Buy. The power cord is not unique to the monitor.

Mag Innovision lt456s 14 in. Flat Panel can find adapter

no never use those one
it will belt ur curcuit in ur moniter
my friend lost his monitor juct cos of it

buy a new proper one

Monitor Message = "No Signal"

see i use Compaq too
they don't generally except other modes

did u try that monitor with other pc where it worked

u should install proper monitor software ... u will found it from the cd given wit Ur monitor


Mag lt456s power supply bad

The correct one would be 12v @ 2.5 to 3 Amp.
If the set used less current than 1 amp it would be in milliamp (500ma which is half an Amp)etc.

As long as you get one that is 12v @ 2.5 to 3 amp it will be fine.
You could buy one with a higher current rating like 4,5,6 or more Amp's as long as it's 12v DC. The set will only use the current that it needs to function so I higher current won't hurt. It's the voltage you have to make sure is correct. If you do buy one with a higher current rating it will probably last longer because it wont get so hot.
Not finding what you are looking for?


Ask a Question

Usually answered in minutes!

Top Mag Innovision Computers & Internet Experts

Cindy Wells

Level 3 Expert

6491 Answers

Joseph Hoffmann

Level 3 Expert

1756 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

49847 Answers

Are you a Mag Innovision Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides