Question about Kenmore 44832 Front Load Washer

1 Answer

Kenmore front load washer 3.5 cubic feet

Washer won't turn on. Lights are on and when start button is pressed makes a sound(locks door) and then all lights go off.

Posted by Roger Marrero on

  • Anonymous Mar 23, 2014

    Lights are on but when I press start. Nothing happens. It just clicks

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 619 Answers

Power line are shorten/put clamp meter on line of the power cord monitor during staet button it go high amphere motor or line have problem, testmotor clamp one line of motor start having high amphere the motor have problem , test capacitor if open replace it /check motor smell smell burning if none test coontinuity if ok capacitor is problem.

Posted on Jan 07, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My Kenmore front load washer will not fill--it sounds like it is draining instead. The last load washed did not spin correctly and the clothes were very wet when cycle completed.

Washer Not Filling:


  • Door Not Closed and Locked
    • Front load washers won't fill if the door is not closed and locked. Listen for the door locking when starting a cycle, then pull on the door to make sure the door is closed and locked.
  • Delayed Start Feature
    • Some washers have a delay prior to filling, where the electronic control is checking the dispenser function. This is Normal.
  • Flashing Lights or Error Code on Display
    • When there is a filling issue, the washer may shut off and display one of the following codes: LF, LE, nF, IE, FH, E10 or F20.
    • If the washer is displaying one of the above error codes, then do the hard reset procedure listed below.

If the appliance is not accepting input from the control panel, follow the steps below to reset the control:

  1. Unplug or turn the circuit breaker off for 30 seconds.
  2. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.
  3. Press the Pause / Cancel / Stop button twice to clear the display.
  4. Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.
0helpful
1answer

My kenmore front load washer doesn't want to start all lights are working but nothing happens even the door won't lock

your door switch is the problem,where the door latch goes into the machine a little switch sites behind this a safety feature and if this is broke the machine will still switch on but will not work it will need replaced they are cheap.adrianxxx
0helpful
1answer
1helpful
1answer

When I try to use the washer I press the Express Wash Cycle as usual. The panel lights up as usual but when I press the start button it dosen't start. I don't hear the front load door lock as usual and...

Hi from retired Englishman in SW France,

'F' for fault, 'dL' for door lock and you don't hear it operating. It's pretty clear there is a problem either with the lock operating solenoid (highly likely 'cos you don't hear it operate) or the door lock sensor (not so likely).
Either you need to replace it or it needs replacing by a service engineer. Sorry, no other option ;-0(

Good luck,
John C
2helpful
2answers

What's the capacity size for a Kenmore 41741042000 washer

4.3 cubic feet
with a loadable space of 3.9 cubic feet
you must leave a gap at the top so the cloths have sopmewhere to move as they tumble
2helpful
1answer

It won;t power up at all, clothes... Solve It won;t power up at all, clothes are locked inside, no lights on the panel. Plug in is working, I... (More) It won;t power up at all, clothes are locked inside,...

This advice is for Kenmore Elite and Whirlpool Duet model front loading washers. If you experience a problem where the door becomes jammed and will not unlock or open, here's an easy way to gain access inside your washer WITHOUT calling the repairman.

1. Remove the lower panel under the door by loosening the three screws under the bottom edge on the front of the washer. HINT: If you prop up the front feet of the washer with some small blocks of wood, this will make access to the screws much easier.
2. With the screws removed, the lower panel should drop down then come off. If the panel sticks, a light tap on either side will knock it loose.
3. Reach your hand up inside the washer behind the front casing on the right-hand side. This is where the door latch assembly is located.
4. At the bottom of the door latch assembly is a small pull tab. This is the manual release for the door. Pull the tab straight down and the door will come open.

Sometimes these doors will not unlock for whatever reason. If there are no error codes being generated, this could have just been a momentary glitch. If you see "Fdl" "DLE" or "Fdu" error codes, these are usually indications of a failed door latch assembly and will require replacement.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
0helpful
1answer

Door locked indicator light flashing

This advice is for Kenmore Elite and Whirlpool Duet model front loading washers. If you experience a problem where the door becomes jammed and will not unlock or open, here's an easy way to gain access inside your washer WITHOUT calling the repairman.

1. Remove the lower panel under the door by loosening the three screws under the bottom edge on the front of the washer. HINT: If you prop up the front feet of the washer with some small blocks of wood, this will make access to the screws much easier.
2. With the screws removed, the lower panel should drop down then come off. If the panel sticks, a light tap on either side will knock it loose.
3. Reach your hand up inside the washer behind the front casing on the right-hand side. This is where the door latch assembly is located.
4. At the bottom of the door latch assembly is a small pull tab. This is the manual release for the door. Pull the tab straight down and the door will come open.

Sometimes these doors will not unlock for whatever reason. If there are no error codes being generated, this could have just been a momentary glitch. If you see "Fdl" "DLE" or "Fdu" error codes, these are usually indications of a failed door latch assembly and will require replacement.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
5helpful
4answers

Kenmore Front Load Washer 417.44152400 lights up, no activity

Find the button on your panel with a 'key' symbol. Press & hold this down till the lock light goes off. Or

Hold down the 'options' & 'select' buttons together till the lock light goes off. Or
Press and hold down "end of cycle"
Pl. rate & tell me what did it - it is important.
0helpful
1answer

Kenmore HE3t lights up ,won't start

sounds like a door lock/latch issue, its not recognizing your closing door so its not starting unit
Not finding what you are looking for?
Kenmore 44832 Front Load Washer Logo

115 views

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Paul Carew

Level 3 Expert

3573 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...