Question about Whirlpool Cabrio WTW6600SBT Top Load Washer

1 Answer

My washer got out of balance and it stopped. now it won't start, and start button is flashing

Posted by kvissing46 on

Ad

1 Answer

craig cole

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 17 Answers

U have to relevel the tub and washer

Posted on Jul 15, 2012

Ad

3 Related Answers

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: error code FL flashes and

FL error - Flood condition

"FL" flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed.

With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Press STOP/CANCEL to clear the display.

You coudl se this manual: Service_Manual_PDF

Hope this helps.

Posted on May 20, 2011

Ad
kevin_getz

Kevin Getz

  • 1032 Answers

SOURCE: I have a whirlpool wfs1072Aw 7.5kg washer that has stopped spinning and won't start even the wash cycle

You probably have either a bad gearcase, timer, or lid switch. Defective motor is also possible.

Posted on May 08, 2012

alsouqi

  • 1 Answer

SOURCE: Start button blinks; won't empty; won't leave wash cycle

turn your dailer to spin cycle

Posted on May 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

White Balance pre icon won't flash


After selecting "PRE" you are releasing the WB button and then pressing and holding it?

Mar 14, 2013 | Nikon D7000 Digital Camera

1 Answer

Kenmore Elite Model 110.42926 202 after setting the desired cycle will not start when you push the start button


see this causes and fix it. God bless you
Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.



Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.



Line Fuse If the washer won't start the line fuse might have blown.



Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.



Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.



Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.



Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
10_5_2012_7_06_37_pm.jpg

Oct 05, 2012 | Kenmore Elite 45986 Front Load Washer

2 Answers

My whirlpool cabrio washer #wtw555oxwo won't work. The lid lock light keeps flashing and the washer won't start


Possible that the switch is defective, there is fault in the line to the control unit from the switch of the control unit is faulty.
check these one by one.

Sep 03, 2012 | Whirlpool WTW5550XW Energy Star Qualified...

1 Answer

Frigidaire front load washer model LTF7000ES0 got out of balance with a heavy pillow and we had to stop it. Now it won't do anything. Everytime I start it, the door light comes on as usual, then a


Check to see if the door sags at all and doesn't line up correctly with the door latch. Then check to see if the drum wobbles when you rotate it yourself when not in use.

Jul 30, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

My washer spin and unlock button starting flashing and when I try to unlock the washer, it won't let me. I have a feeling the load was off balance. What can I do to unlock it?


Access the drain hose and get the end to ground level in a bowl. Empty any water. Clear filter and make sure drain pump is free. Door will now open

May 19, 2012 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Washer will start then stop and the no spin light comes on and wont go no further


Check the springs and dampers are all in place. The machine thinks it is out of balance and won't spin until it's rectified.

Apr 22, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Can't stop cycle


You probably have some other issue with the machine if it won't stop, but the machine may also not be spinning the mat out because the load is unbalanced. If you put it in on spin only, watch to see if it actually spins up to speed or not. You will see it rotate the drum back and forth a couple of times - it is sensing the weight of the load and trying to balance it. I the machine can't balance it, it will never spin up to max speed. If this happens, put a few other items in the washer with the heavy item (they need to be of similar weight - like some towels or a heavy jacket or something) and try again. Good Luck

Apr 18, 2012 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Whirlpool Cabrio WTW6600SBT Top Load Washer Logo

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18397 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...