Sound There is no sound when i hooked up receiver to tv, matched colored cables from receiver to tv .when i change from tuner to cbl/dtv theres no sound. thanks

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.
Contributor
1 Answer

I'm assuming you you have a basic TV to receiver hookup. Make sure you have the TV audio video output going to the receiver input.

Posted on Sep 01, 2007

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Receiver and TV not communicating well. No video on TV !

Try changing your AVI cables, the yellow one could be causing the problem.
Try plugging the your cables into the spear ports at the front of the tv if it has them.

Read full answer

Oct 12, 2012 • Yamaha RX-V757 Receiver

0helpful

1answer

Unable to get surround sound thru all speakers

Some features do not give surround sound such as tuner. If input cables attached to analog dtv/cbl and speaker cables attached to wire end output serround should work fine when set to dtvcbl on front display.

Read full answer

Mar 31, 2011 • Yamaha HTR-5850 Receiver

0helpful

1answer

I can't get a sound from my yamaha rx-v367. my tv is lg le5310

Last update: 05/02/2008
Connect the audio outputs jacks from the TV to any available audio input terminals on the Yamaha receiver, other than the phono input. You can use any analog audio Left (White) and Right (Red) inputs on your receiver such as the DTV/CBL, SAT or VCR input. There are no special settings needed on the receiver, other than selecting the correct input. There may be some settings that will need to be changed on the TV. Consult the TV ownersEmanual for setting up the TV to output audio to an external source. If youre TV has a digital output (Optical or Coaxial) it can also be run to one of the digital inputs on the Yamaha receiver, such as DTV/CBL or DVD. There may be some settings that will need to be changed on your TV. As always, consult the TV ownersEmanual for setting up the TV to output digital audio to an external source.

NOTE: When the source of the audio signal is coming from an HDMI device connected to the TV, the TV may not output in 5.1 surround sound.

Read full answer

Jan 01, 2011 • Yamaha RXV367 Receiver

0helpful

1answer

My HTR-6060 plays through the tuner and dvd but not the DTV/CBL

Digital settings need to be assigned by the receiver in the ption Menu >> Audio Select.

Check the one for the HDMI from DTV/CBL.

Read full answer

May 23, 2010 • Yamaha HTR-6060

2helpful

1answer

Sound from tuner but no other devices

The RX-V365 cannot process audio from the HDMI cables (you will still be able to hear it on your TV), you will need to run a seperate coaxial or optical cable into the audio input for the relevant component on the back of the RX-V365.

Read full answer

Dec 26, 2009 • Yamaha Rx-v365 A/V Home Theater Receiver

1helpful

1answer

Yamaha HTR-5750 no sound when I turn to the DTV/Cable setting

If you are not getting sound on "Any" input except "multi channel" you have a bad DSP chip in the receiver.In short, you need a new receiver, it's a 500.00 repair. If you get sound on "All" inputs except "DTV/CBL" You need to get into the main menu of the Yamaha and select audio, toggle to input, then DTV/CBL and select "Auto". If you still do not get audio, it would be due to the version of HDMI software in your receiver. If it's under warranty, Yamaha will update hardware and software for you at N/C. If it's out of warranty, use digital coaxial or optical as your audio input for TV and run your HDMI directly to the TV. (The repair for this too would run 250-350) I hope I've covered all the possibilities. If you need further help, post a comment and I can help you more.

Read full answer

Aug 25, 2009 • Yamaha HTR-5730 Receiver

0helpful

1answer

I have a Zenith TV its has three ports in the rear video/audio left right my cable jumper run out tv to dvd to cable hook up/dvd is playing threw the 6130 but the TV won't play with video/audio jacks hook...

Any audio/video in should work as long as your receiver is set to the same component as the cables are plugged into.

Read full answer

Feb 22, 2009 • Yamaha HTR-6130 Receiver

3helpful

1answer

I need remote control code number for motorola dvr 6416 III

If this is a remote by UEI or Atlas (usually the black remote that the cable company supplys with the box) the code is 1376.

To set the code, you will need to do the following:

Unlock the Cbl button:
Press CBL once. it will blink once.
Press and hold SETUP until CBL blinks twice. Release setup
Press 982
CBL will blink 4 times, indicating it is unlocked

Program the code in:
Press CBL once. it will blink once.
Press and hold SETUP until CBL blinks twice. Release setup
Press 1376
CBL will blink twice if the code is accepted.

Re-lock the CBL button:
Press CBL once. it will blink once.
Press and hold SETUP until CBL blinks twice. Release setup
Press 982
CBL will blink 2 times, indicating it is locked again

If it is not a UEI or Atlas remote, let me know the remote make and model

Read full answer

Dec 01, 2008 • Arris DCT6200 DTV Receiver

0helpful

2answers