Question about Coby MP-C7097 MP3 Player

1 Answer

The mp4 won't turn off

I can only turn it on by pressing the reset button, and when i turn it off the keypad stays lit which wastes the battery

Posted by on

  • hiba566 Dec 09, 2008

    its not on hold and i do hold the powre button until it turns off. the keypad doesn't turn off though.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,597 Answers

Make sure the hold switch is not turned on. If not, then hold the power button until the player turns off.

Posted on Dec 09, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ink absorber full


What model is it?

General reset:

How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Dec 02, 2010 | Canon Office Equipment & Supplies

1 Answer

Ink absorber is full


How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Dec 01, 2010 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

WASTE INK ABSORBER


How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Nov 30, 2010 | Canon PIXMA iP90 Mobile Printer

1 Answer

How do I change, remove, or clean the ink waste tank on a canon MP390? "Waste Ink Near Full" error is showing up. Canon Service wants $125-$150 to clean this - more than a new printer. How to I dismantle...


Try to reset your printing by doing these:

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button 4 times, the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Turn off the printer.( it must be turn off)
then turn it on again.

Courtesy of Indoreset Yahoo Group

Jul 20, 2010 | Canon MultiPASS MP390 All-In-One InkJet...

2 Answers

How do i reset a canon PIXMA MP150 printer after the "waste absorber is full" message shows????



1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.( it must be turn off)
then turn it on again. this works. thanks.


If you need further help, reach me via phone at https://www.6ya.com/expert/joel_63c670a84e9f6a97

Nov 07, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Canon PIXMA MP110 waste absorber is nearly full


Hi

Thanks for using FixYa. Open the cover, move the cartridges to the centre, and then press the pad of absorbent paper towel onto the waste ink pads. You can locate the waste ink pads to the right of the cartridges. This will absorb a lot of ink in the pads and that will remove the warning after you reset the printer waste ink tank counter. You can reset your Canon Printer by following this procedure—

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button 4 times for waste ink counter reset.
5) Turn off the printer.( it must be turn off) then turn it on again.

Please do rate the solution and revert for further assistance.

Thanks
Rylee

Sep 11, 2009 | Canon Office Equipment & Supplies

1 Answer

WASTE TANK FULL


How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Apr 16, 2009 | Canon MultiPASS MP730 All-In-One InkJet...

1 Answer

Cannon Pixma MP160. on/off light keep blinking and won't print


This some times works.

Also if you are using the Refillable ink cartilages stop they always cause major issues

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)Note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.(it must be turn off)
then turn it on again.


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one and to go on helping.
All The Best: Pineworks

Mar 15, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Change code on keyless entry. Now the remote does not work.


Did you clear the codes existing in the unit? (Press and hold the learn button; LED light will stay lit for approx. 6 seconds.) If you have remotes that have dipswitches, pop the battery cover off and make certain that all switches are set identically in each remote. Now, press the learn button on the main unit and immediately release. While its LED light is lit, press the button on ONE of the remotes only. They will ALL be programmed at this point. Now, press the learn button once more (quickly and release) and enter your number code on your keypad and press enter. It should be programmed now, too.
I was having a similiar problem, and this turned out to be the solution. Before, I was programming both remotes, not knowing as I did so that by programming one, and then another, I was UNprogramming the the first as well as the keypad.
I hope this works for you. It did for me.

Jan 23, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Razr- turning on camera makes screen turn black but keypad stays lit


the easiest thing tpo do here is take it to a professional but if you want to try updating your software off the Motorola website. (this require a data cable or bluetooth in your computer) This fixes a lot of software problems with the razor. If this doesn't work then you will have to reflash your Firmware which is like the Windows Xp of the phone. This does require a professional as it can destroy the phone

Jul 05, 2007 | Motorola Mobility RAZR V3

Not finding what you are looking for?
Coby MP-C7097 MP3 Player Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coby Audio Players & Recorders Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Ekse

Level 3 Expert

13434 Answers

Cindy Wells

Level 3 Expert

6074 Answers

Are you a Coby Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...