Hotpoint Aquarius WMA52 Front Load Washer Logo

Related Topics:

Question about Hotpoint Aquarius WMA52 Front Load Washer

1 Answer

How do i remove a rear control knob on a hotpoint wma50s machine

How do i go about removing a rear control knob on a hotpoint aquarius wma50s so ican replace abroken on the part number i have for this knob is 1603391 Yours Dennis . B

Posted by Anonymous on

1 Answer

peter gittos

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 247 Answers

To replace your timer dial take the lid of by unscrewing 2 screws at the back of the lid were your dial is look down a small oval shape opening u will see a screw undo it and the dial will come off m8

Posted on Aug 15, 2007

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Can someone please share Hotpoint WMA50 schematic diagram?

Hi thanks for question.
https://www.manualslib.com/manual/71009/Hotpoint-Aquarius-Wma50.html?page=10#manual
1helpful
1answer

My hotpoint washing machine (model wma50) will not start due to the door lock light flashing yet the door is closed

common problem on these machine's, you need a new door handle which comes as a full assembley with spring and all attached.

open the door, using star screw driver remove top and bottom screws along with two near the catch.

the doo wil split enough to remove old handle and fit new 1.




0helpful
1answer

Motor brushes....how do you change them

Remoe lower rear cover of washer.
Remove earth wire, and unplug motor socket.
Remove belt and remove 2 bolts securing moor. holding moior, lever motor towards rear, and remove motor from washer.
Change the brushes in the motor.
0helpful
1answer

Where is the water filter kept on the hotpoint aquarius wma50

Remove lower rear panel of washer, locate and remove large black hose fastened to bottom of drum, filter is located inside the hose.
1helpful
1answer

Hi, i have a hotpoint aquarius 6kg wma50, my

Have you checked for blockage in the pump. Or the have been some problems with a ball that sits in the hose between pump and the drum. This can block the water. Check this berfore purchase new pump.
18helpful
1answer

Where is the filter on the Hotpoint Aquarius washing machine?

Filtet access at the rear of the machine behind access panel, Remeber to remove the plug from the socket before removing the rear panel
0helpful
1answer

Hotpoint aquarius wma50

The motor does not have provision for belt adjostment, it is self tensioning
To gain access to the brushes, you need to remove the motor from the washer.
Remove rear panel, remove belt, unplug motor lead, taking note which way the plug goes,undo screws securing motor, and lever motor back with a screw driver, remove motor and change brushes.
3helpful
1answer

Noise when draining

U will find the filter by removing the lower rear panel of the m/c.
Locate the large black hose at the right side, and remove clip securing hose. Get some thing ready to catch any water that will be in there, and remove hose.
There u will see the filter, remove and clean, refit filter and hose,making sure that u get the hose on properly, test for leaks before u put the panel back on.
U will find this much easier to do if u tilt the m/c forward, and support it with something underneath.. Check inside the pump as well.
Plz rate my solution.

Thanks.
1helpful
2answers

I need to change the door seal on a Hotpoint Aquarius WMA50

Basic diy tools should be ok. Take out lid screws behind plastic caps on edge(will be stars but small flat will do it).Lift front of lid and push back to remove.Remove kick plate and take out screws behind it.Remove band holding front end of seal and detach seal from rim of opening. Remove screws holding door lock and push lock through. Remove soap drawer & take out screws behind it.Carefully bring panel forward & slide to right to remove(Take care here with board &wiring)Remove screws holding front panel & lift front panel & remove it.Remove band from seal and your there.Note locating slot on seal. If possible get an extra pair of hands to hold panel with board to avoid damage.
Not finding what you are looking for?

212 views

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

2515 Answers

Paul Carew

Level 3 Expert

3763 Answers

Cindy Wells

Level 3 Expert

6650 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...