Question about Sony KP-57WV600 57" Rear Projection HDTV-Ready Television

1 Answer

I have a sony KP-57WV600 Big Screen Rear projection television. The problem is this: When I first turn the tv on the picture is fine, than after it warms up- the screen turns red. What would the problem be.

Posted by lori_fischer on

  • Chief9Ice Jan 01, 2009

    As soon as I turn on the tv (Sony Projection tv KP-57WV600), the tv comes on, then goes to green the goes off... The red light blinks 7 times...



    Thanks

  • sonystuff123 Apr 20, 2009

    I have the same TV and the same problem.  When the TV is turned on the red tint starts to creep in, then it goes pretty much completely red before the picture just disappears.  The standby light then blinks several times in a row and doesn't stop once the TV has been powered off.  Is the tube shot?

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,594 Answers

Let me know when TV warms up does it go to standby?
If yes, standby light would be blinking, let me know how many times it blinks?
And if TV does not go to standby mode, does picture remain with red tone?

Posted on Dec 06, 2008

Ad

1 Related Answer

Anonymous

  • 13 Answers

SOURCE: Sony wide screen projection tv model kp-57wv600.

I found this solution from SONY's website.

The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.

  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.


I hope this helps.

Posted on Aug 05, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
1helpful
1answer

Sony Projection TV problem

sony rear projection KP series are know for having bad utbes after while..ihad seen the blue tube goes on most.
1helpful
1answer

Sony wide screen projection tv model kp-57wv600 problem. Sound with no picture. Stanby red light blinks seven times? What parts do I need to repair the problem. Thanks ,Gary

I found this solution from SONY's website.

The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.


I hope this helps.
2helpful
1answer

Sony goes blue

you need a new Blue CRT you can get them at the following link.
http://servicemanuals.vstore.ca/
0helpful
1answer

Cleaning the screen cover on my sony big screen

Hi,
To clean its front screen, you should not open front cover as its complicated procedure. just take off its back cover as its shown in picture and use air-blower to clean dust. Then use soft cotton cloth to clean its screen from internal and 3 bulbs / lenses (CRTs) and job is done.
Need further help, let me know.
Bye.

3a6cab2.jpg
0helpful
2answers
0helpful
1answer

Sony KP-57wv600 big screen

you will need to replace the Green CRT your model uses the sony # 873365201 CRT. The other site I work for just got a shipment of Sony and RCA CRTs(Tubes) in on friday. So you can get one at the following link these are brand new Tubes and they provide free shipping and free on line tech support with instant messageing in case you need help installing it. Heres the link.
http://servicemanuals.vstore.ca/
0helpful
1answer

TV going to from blue to black

You both have a bad high voltage Trippler block.
0helpful
2answers

Sony KP 57WV600

how many times does it blink?
Not finding what you are looking for?
Sony KP-57WV600 57" Rear Projection HDTV-Ready Television Logo

Related Topics:

522 views

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76823 Answers

Ekse

Level 3 Expert

13435 Answers

Nasir Muhammad
Nasir Muhammad

Level 2 Expert

252 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...