Question about Siemens SpeedStream 4200 (13A4200001) Bridge

Open Question

Real slow put a drive belt on and then it want go very fast

Posted by patrick stroupe on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag washer is sometimes out of balance and clothes are sopping wet when spin cycle ends. Washer is balanced on the floor.


1ST thing put less clothes in washer each time

second ck to see that drain hose is not obstructed from draining out the chamber , ive seen fabric lint get stuck inside the drain valves and slow and eventually block them off

last thing to look at
temp defeat the lid lock switch and or watch it spin thru window , your looking for the speed it spins at (should be a blur !!) , if its slow and not steady in rate but instead sort of gets slow/fast/slow/fast this could be an indication that your tub drive system isn't working well , this depends on a large bit of things working properly , but could be as simple as a worn out drive belt too.

Feb 03, 2017 | Maytag Washing Machines

1 Answer

Turntable running slow


Hi Ken,

it is a Technics Frequency Generator Servo (Belt drive SL-23). I have four different belts and neither one of them works. Two are too slow and one is too fast and the other one is slow and fast.

I changed the belt before that I got off of an old turn table. It deteriorated.

I would appreciate any help.

So far I am also having Gateway Monitor problems and Canon Mp560 printer problems

Thank you,.

Aug 23, 2014 | Audio Players & Recorders

2 Answers

Alternator/battery problem


either drive belt too too big or drive belt tensioner broken or drive belt need adjustment if you have v type belt.

Apr 25, 2013 | 1992 Mazda MX-3

1 Answer

Need to put on new fuel pump, gas tank is full, when trying to cyphon it out it just drips real slow


u'll have to drop it full then. or u didnt get enuf gas in the hose. use a clear hose so u can see the gas and **** real slow till you see gas then put down to ground fast till it starts flowing, good luck

Dec 28, 2010 | 1994 Buick Roadmaster

1 Answer

It plays records a liiiittle bit too fast. How do I fix that?


my 1960's solution was to Put a few pennies on record , and the real cause is your drive belt may be too tight.

Aug 26, 2010 | Memorex Nostalgia 4-way Stereo Shelf...

1 Answer

Riding mower goes slow in forward speed


There is a variable speed pulley that is a double pulley....one belt from engine to pulley and one from pulley to transaxle....remove both belts...pushing in the clutch will help with removal....remove o ring on top of pulley and pull up......the middle piece of metal is stuck....this piece is meant to slide up and down.....put the middle piece of metal on your pulley in your vice...wd40 the hell out of the shaft on pulley .....grasp the top with one hand and the bottom with your other hand...work the stuck pulley free.....put lithium grease on shaft...reinstall....done

Mar 09, 2009 | Mtd Garden

1 Answer

I have a Denon 300f that works fine but run a bit fast so the music sounds really off...anything I can do to slow it down?


I was putting the belt around the wrong part...it needed to go on the bottom of the turntable itself then be attached to the belt drive.

Jul 17, 2008 | Denon Audio Players & Recorders

1 Answer

Maytag performa washer


Hi Folks,

I'm guessing both of these problems are related to the belt slipping. There are several points to check.
  1. the belt tension. I'm not familiar with the exact details of your machines, but the usually have a an extra pulley with a spring attached to give the belt tension. Alternatively, the motor is mounted on a movable frame that is held by some springs. These springs give the belt tension. In either case check the freedom of movement of the tensioning arrangement and the springs are providing the necessary tension to the belt.
  2. Glazed belt/pulley - if the belt has been slipping it will polish the pulleys and this will reduce the friction necessary to drive the machine. To fix this the belt should be replaced and the pulley surfaces roughed up with some wet/dry emery paper (not too rough or it will wear your new belt out).
  3. Belt is too old - the rubber becomes hard and brittle and ends up with the same effect as Glazed belt/pulley above. The fix is as per 2 above.
Good luck
Bob Thompson

Dec 12, 2007 | Amana NAV5800A Top Load Washer

1 Answer

Spinning slow and smells like burnt rubber. Draining very slowly.


Pull drain plug at bottom of machine put tray under it check belt

Dec 18, 2017 | Amana NAV2330AW Top Load Washer

Not finding what you are looking for?
Siemens SpeedStream 4200 (13A4200001) Bridge Logo

Related Topics:

222 views

Ask a Question

Usually answered in minutes!

Top Siemens Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2278 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Siemens Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...