Power Problem I have not used my computer in about 3 months. It has been untouched for that time (the room door closed, no kids, etc). When I attempted to get on the computer, there was no power to the tower. I double checked the cords, they are in the right place, plugged in tightly, etc. Tried different outlets and different power cord. Monitor and perifpherals all have power. What could it be ??

The door switch does sound more likely, and is a good place to start. These switches are well known to be intermittent at times.

Simple way to pay less bill with big comfort.
Tips for it: To get proper cold air set temp 23 degree and mode"cool". To get heat set temp 30 degree and mode in "Heat" Clean indoor and out door periodically ( Once in 4 months) Clean Air filter every fortnightly. Avoid frequent opening of the door where it's air conditioned. Avoid keep closing the doors even a/c is switch off. It helps to cool the room next times in short minutes. Use proper breaker, wiring for your air conditioner plug points. Make sure your elect meter is working properly.Check your Elect meter with 1000watts bulb for one hour. It should consume one unit only. Hope, it's helpful.

it happens at times.. switch off the laptop by pressing the power button for say 10 secs till u notice its off. then switch on as usually. once the operating system is loaded go to desktop ->right click->properties->screen saver->power-> 1.hibernate->uncheck hibernate. and to change closing the laptop lid actions go to 2.advanced->when i close the lid of my portable computer->do nothing
and doin so ur laptop ll be left untouched even when u close de lid. try t out !!

IMPORTANT: Read thoroughly. DO NOT add detergent or other laundry products to this cycle.
1. Remove all items from the washer.
2. Open the dispenser drawer and 2/3 cup (160 mL) of liquid chlorine bleach to the bleach compartment. DO NOT use more than 2/3 cup (160mL) of bleach per cycle as this will lead to product damage.
3. Close the washer door and dispenser drawer.
4. Select the Clean Washer cycle or a full wash cotton 104 F wash (40 C). DO NOT use any higher temperature as this will cause unnecessary fumes
5. Press Start and allow cycle to complete.
6. If the bad odour persists, repeat the procedure 1 or 2 more times. This may be necessary if this is the first time you have run this cycle.
7. After the cycle is complete, leave the door open slightly to allow ventilation and drying of the washer interior.
8. Repeat the cleaning procedure monthly.
To maintain the washer freshness:
1. Use only HE High Efficiency detergent.
2. Leave the door open after each cycle to for better ventilation and drying of the washer interior.
3. Use warm / hot water in your machine unless the fabric you are washing requires cold.
4. Use the correct amount of fabric softener.
5. If your laundry room is damp, use a dehumidifier.
6. Clean the door seal of visible residue.

It's the ducting that causes the problem. But if the old unit wasn't as bad, did they install a smaller unit to save on money? It is possible, some companies do this to make more money. Sad but it is true. A return added to the room would help but if they can run a return, then they can add another duct or reduct the room as well. Sounds like someone is trying to sell you a story without fixing the issue. Tell them that they don't need to add an extra run, tell them to change the size! Also, make sure that if the run is longer than 25 feet, the ducting has to be stepped down in size to increase valocity to the vent. For example, you have a 10" duct running for 25' and then you step down to 8" the rest of the way unless that run is more than 25'. Hope this info helps!

the problem could be the latch motor gears are stripped or stripping. try unplugging the range. push the door closed then connect power to the range. keep pressure on the door for about 1 minute then check if the door opens.

2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Try "resetting" your keyless entry code. Which is a fancy way of explaining that I broke my keyless entry key fob and had to order a new one. It came w/ instructions explaining how to get the new fob to speak to the car's computer. It was weird (turn key on and off 3 times, open and close door three times, etc. **I'm sure my neighbors were watching and laughing**), but it worked. I'll scan and email you the insrtuctions if you wish. Dan: [email protected]

Sounds like the ice door in the dispenser isn't closing properly or all the way which lets warm air in condensates then freezes.