TV won't "talk" with satellite cable

If you are receiving a "No Signal" error message, verify that:

1. All of the cables physically connected to the TV and the input device are secure.
2. The input device is turned on.

Your TV needs to scan for channels before it can show programming from an antenna, from cable TV when the cable comes directly from the wall (no cable box), or from a cable or satellite box connected to the TV with a coaxial (RF) cable. Do not scan for channels if you have a cable or satellite box connected using AV (Composite), Component, or HDMI cables. The box selects the channel, not the tuner inside your television. If you are not using the "TV" input, press the INPUT button on your remote until the correct input mode is selected.
To perform a channel scan using the coaxial input:

1. Press the INPUT button on your remote to view your current input source. The TV (coaxial cable) input must be selected. This may appear as "TV," "ANT," or the channel and call letters of a station.
2. If the TV input is not selected, press INPUT until the TV input mode is selected.
3. Open the on-screen menu and select TV or Tuner option. (This varies by model.)
4. Highlight Tuner Mode and select the correct option:
   • Antenna-over-the air signals from an antenna
   • Cable-direct from the wall cable TV, or a cable or satellite box connected to the TV with coaxial cable
5. Select Auto Search or Auto Channel Scan. (This varies by model.)
6. When the search reaches 100% complete, exit to the menu.
7. Check the available channels:
   • Antenna or direct-from-wall cable-Press the Channel Up and Channel Down buttons on your VIZIO TV remote to view the available channels.
   • Cable or satellite box- Will return only one channel. Use the cable or satellite remote's Channel Up and Channel Down buttons.

If this does not resolve the issue, power cycle the TV and then re-run the channel scan:

1. Turn off the TV.
2. Unplug the TV from the electrical outlet.
3. While the TV is unplugged from the wall, press and hold the Power button on the TV for 30 seconds.
4. Release the power button.
5. Plug the TV back into the electrical outlet.
6. Turn on the TV.

Note: There is also an option to reset the TV to the factory default settings. This option is in either the SETUP or SYSTEM section of the on-screen menu. The option may be "Reset all settings", "System Reset," or "Reset & Admin." Consult your TV's user manual for the location and steps for resetting your model.

1. Remove the coaxial cable from the DTV/TV connector on the back of your television and perform a channel scan to clear the existing channels. See the procedure above. This should not find any channels.
2. Re-attach the coaxial cable to the DTV/TV connector and perform a new channel scan.

This video shows troubleshooting steps to use when a "No signal" message appears.

TRY THIS

1. • 1 Turn the TV off with the front-mounted power button, not the remote. Unplug the TV's power cord from the wall outlet. Let an hour pass before plugging the cord back into the wall outlet. Turn the TV back on with the front-mounted power button and wait until it has fully restarted. Bring up a TV channel to see if the image being presented on the LCD screen is no longer flickering. A momentary power surge can cause the circuitry inside the LG-brand LCD TV to function erratically.
     
   • 2 Unplug the video cable from the video connection on the back or side panel of the LG TV. If more than one video cable is connected to the TV, disconnect all of them. Disconnect the other end of the video cable from the video source device that it's attached to -- a DVD or Blu-ray player, or a satellite receiver or cable box. Blow off the connections on the video source device and on the back or side panel of the TV with bursts of compressed air. Reinsert one end of the video cable into the video source device and the other end into the video input that it was connected to. Turn the TV back on with is remote to see if the picture is now free of flickering. A loose or partially connected video cable can cause the LCD TV's screen to flicker when presenting an image.
     
   • 3 Turn the TV off and unplug its power cord from the wall outlet. Place a power conditioner next to the wall outlet. Plug the power conditioner's power cord into the wall outlet. Plug the TV's power cord into one of the AC sockets on the power conditioner. Turn the power conditioner on. Turn the TV on to see if the picture is now free of flickering. The RF signals in the electric line that the LG TV is drawing power from can cause flicking through interference patterns being generated.
     

Hello
You just try one the procedure given below. One amoung will lead you to its service mode.

Unplug the power cable.
* Press and hold the {MUTE} button on the remote control while plugging the power cable back into the outlet.
* Keep pressing the {MUTE} button until the TV powers on with the Service Menu displayed.
* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.
* Some menus might have sub-addresses. Use the numeric buttons {0} to {7} to adjust sub-item data.
* Press the {MENU} button or turn the TV off to exit.
*******************************************************************************************************************

Unplug the power cable.
* Press and hold the {VOL -} button on the TV
while plugging the power cable back into the outlet.

* Keep pressing the {VOL -} button until
the TV powers on with the Service Menu displayed.

* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.

* Some menus might have sub-addresses. Use the
numeric buttons {0} to {7} to adjust sub-item data.

* Press the {MENU} button or turn the TV off to exit.

Hello

In time as the Sony Trinitron ages it begins to have power issues. While this can be true of most tube televisions it's the rate and severity at which this happens to Trinitrons that makes it particularly of note. Many Trinitron owners have complained of the Trinitron set turning itself off randomly and frequently. Some sets have failed to stay on for longer than a few minutes at a time. Eventually some sets will not turn on at all. These problems grow more severe with age.

Check the power cable running from the Sony Trinitron 32. Make sure the cable is completely inserted into the power connection on the rear of the TV as well as the local power outlet.

Disconnect the power cable from the electrical outlet, then plug it into a different connection. It is possible to electrical outlet has died, forcing you to obtain a power current from a different source.

Check the cable connection running from the cable/satellite receiver or VCR. If the TV is on but no picture is on the screen, the problem is most likely due to a connection issue.

Power off the cable/satellite receiver, then press the "Video" button on the remote control to switch the Trinitron 32 to the video input signal. Turn on the cable/satellite receiver and the programming now loads onto the television screen.

You probably switched the TV from analogue to digital mode or vice-versa.

There should be a small button on your remote control marked DTV or ATV. Try pressing this.

If you are using a separate cable/satellite/tuner box from a SCART cable, turn off the tv, and turn off the cable/satellite box. Then turn the TV back on, then the cable/satellite box back on. The TV should recognise there is an external input and you should be OK.

Hello. I may be able to assist you. If you are using a direct cable connection from the wall outlet;

• Check the incoming cable or antenna signal connection to ensure that it is properly secured to the TV's antenna input.
• If the connection is good, perform the automatic installation again to search for all available channels.

If you are using a coaxial connection from the Cable or Satellite box to the TV;

• Set the TV to the channel specified by the service provider.
• Change the channels at the Cable or Satellite box to view the program.

If you are using a video connection (CVBS, S-Video, YPbPr, HDMI) from the source (DVD, Cable or Satellite box) to the TV;

• You do not need to perform automatic installation to search for the channels.
• Press the 'SOURCE' button on the remote control repeatedly to select the correct input source.

If you are using an HDMI connection from the source (DVD, Cable or Satellite box) to the TV;

1. Reset the TV and source by unplugging it from the power outlet for 30 seconds.
2. Turn on the TV and press the play button on your source device. If the source is HDMI CEC compliant, the TV will automatically switch to the HDMI input.
3. If your source is not HDMI CEC compliant, turn on the TV and switch to the HDMI input.
4. Turn on your source.

If you are sure you have selected the correct input or channel but still have no picture or sound;

• Try resetting the TV by unplugging it from the power outlet for 30 seconds.
• Press the 'SOURCE' button to select the correct input source.
• Check the connection cables.
• Try the connected source with another TV.
• Connect a different source on the same connection of your TV.

If the TV standby light is blinking for five times then you may perform the steps given below:
(i) Turn off the TV then disconnect all the cables from the TV.
(ii) Next, reconnect all the cables after two minutes.
(iii) Please make sure that the power cable from the TV is directly connected to a functional wall outlet.
(iv) Next, you may try resetting the TV to the original factory settings.

Please follow the steps that are mentioned below to reset the TV to the original factory settings:

(a) Turn ON the TV.
(b) Press and hold the Power button on the Remote Control supplied with the TV, then press the Power button on the TV front panel.
(c) Release the Power button. The TV will turn itself off, then back ON again.
(d) Next, release the Reset button on the Remote control.

If the standby light still blinks then the issue may be with the projection lamp in the TV and requires replacement.

Hi Kevin!

The issue may be related to the projection lamp in the TV and replacement may be required. However, before replacing the projection lamp in the TV, you may perform the troubleshooting steps mentioned below.

Please disconnect all the cables from the TV including the power cable then reconnect them after two minutes. Please make sure that the the power cable from the TV is directly connected to a functional wall outlet. Next, you may try connecting any other video source such as cable box, DVD player, Blu-Ray player, Playstation, etc. If the issue persists then try resetting the TV to the original factory settings.

Please follow the steps mentioned below to reset the TV to the original factory settings:
(i) Turn the TV ON.
(ii) Press and hold the Reset button on the Remote Control supplied with the TV, then press the Power button on the front panel of the TV.
(iii) Next, release the Power button. The TV will turn itself off, then back ON.
(iv) Release the Reset button.

If the issue persists then you may replace the projection lamp in the TV.

Setting Up the TV
After you have finished connecting your TV, you can use Auto Program to set up your
channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.
(Make sure CABLE is connected on coaxial and you are not using any other connections such as cable box, hdtv or satellite antenna)

1 Press to turn on the TV. The Initial Setup screen appears.
2 Press on the remote control or on the TV front panel to start Auto Program, or press
to exit.
To perform Auto Program again
1 Press .
2 Press g to highlight Channel Menu.
3 Press f to highlight Cable. Press to select.
4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select.
5 Press f to highlight Auto Program. Press to search for channels.
6 After Auto Program finishes, press to exit.
To reset the TV to factory settings
1 Turn the TV on.
2 Hold down on the remote control.
3 Press and release the POWER button on the TV front panel. The TV will turn itself off,
then back on.
4 Release .
✍ When you start Auto Program wait until it is finished; otherwise it will skip over channels that are
available. Perform Auto Program again to program receivable channels.
✍ The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.
Initial Setup
Auto Program [CH+]
[CH–]
First please connect
cable/antenna
Exit

Try to reset first if nothing happens we proceed another solution;

Resetting the TV

Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can saved time.
1. Unplug the TV power cord from the power outlet for 6 hours.in order to dessipitate the charge current.
2. Unplug any connected devices (Satellite, DVD, Set-top boxes, etc...)
3. Press and hold the TV power button for five seconds.
4. Plug the TV power cord back into the power outlet and turn on the TV.
5. Open the on-screen menu to confirm that the TV is responding again.
6. Turn off the TV and reconnect the devices.
7. Turn on the TV.

hope this may help;

Regards,
VOTIT