AEG L66600 Front Load Washer Logo

Question about AEG L66600 Front Load Washer

1 Answer

Error code 50

My machine will not fill or start, green LED suggests machine 'thinks' that door is open (it isn't!), If left for 30-40 mins it eventually returns E50 error code. Can anyone help?

Posted by tim kalns on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

I think you should pull out the filter, and clean it. appliance doctor

Posted on Feb 02, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Oce 360 plotwave code error 20501 ???? how to fix

this error more related to software problem,but you need do below step to check their hardware is in good condition.if all ok no problem,you may need to reformat their OS
1.off machine/on machine
2.pls check their controller connection (in you left side back cover down area).Make sure all the port are plug in properties and also in correct location,you cannot plug in to anywhere if no you will get the error code.
3. open fusing door ,try to unlock screw on right side back cover got 3 screw (torx 15 or 20)
4.open that cover look down that area got 1 big spider board.make sure all their connector usb port are plug in properties and in correct location.
5. check the big board should be got 3 LED green light stable on if no use machine.no got red LED on.
6.check that small board are properties install in good position in big board location.
7.check that small board must go 1 LED green light always falshing or stable,if got Red LED light on means this board faulty need replace new unit.

-pba-spider-io-jlmlymhrhxoo2u0djlvt4w5v-2-0.jpg

-spider-pba-jlmlymhrhxoo2u0djlvt4w5v-2-1.jpg
0helpful
1answer

Oce 360 plotwave code error 20501 ????

This error more related to software problem,but you need do below step to check their hardware is in good condition.if all ok no problem,you may need to reformat their OS
1.off machine/on machine
2.pls check their controller connection (in you left side back cover down area).Make sure all the port are plug in properties and also in correct location,you cannot plug in to anywhere if no you will get the error code.
3. open fusing door ,try to unlock screw on right side back cover got 3 screw (torx 15 or 20)
4.open that cover look down that area got 1 big spider board.make sure all their connector usb port are plug in properties and in correct location.
5. check the big board should be got 3 LED green light stable on if no use machine.no got red LED on.
6.check that small board are properties install in good position in big board location.
7.check that small board must go 1 LED green light always falshing or stable,if got Red LED light on means this board faulty need replace new unit.
-pba-spider-io-jlmlymhrhxoo2u0djlvt4w5v-2-0_0.jpg

-spider-pba-jlmlymhrhxoo2u0djlvt4w5v-2-1_0.jpg
0helpful
1answer

Changed door switch on my kenmore h2 plus cause of error code and it still wont work

Whirlpool & Kenmore Dryer Repair #01 - Won't Start or Run ...

? 8:50
https://www.youtube.com/watch?v=2WF71WdGn_g
Oct 19, 2011 - Uploaded by canyonman1963
This one deals with testing and replacing the door switch. ...sears wont work wont spin wont wash wont heat wont start fix repair bad noise noisy ... how to change a 4 to a 3 prong cord, to figuring out my door switch problem.

Dryer Door Switch - How To Replace - YouTube

What to do when your washer won't fill, start or run - YouTube

? 2:00
https://www.youtube.com/watch?v=Atd5YHbRh7M
Jun 20, 2012 - Uploaded by searspartsdirect
So if my washer wont start just call Sears. .... Bad sears mykenmore is only 2 years old, fill take 30 mins,,,wash 50 mins rinse never spin never,, ...


0helpful
1answer

My zanussi zwg 6141p washing machine is calling water at start of cycle but is not going into drawer to swill out detergent , is also stopping half way with the green light on the start button flashin

Some appliances malfunction can be displayed in hexadecimal or in binary code.
So your device is defective and shows you what's wrong. You have to count how many times flashes red light and how many times flashes green light. Red light shows the first error number and green light the second error number.
For example: you forgot to close the door and you started washing machine. After some time (timeout) will generate an alarm. Four times will flash red light and once the green light which means error code " E41 " or "Open door"
" E20 " means "No drain water"
" E10 " means "No fill up water"


Dado
1helpful
1answer

Hi I have a WFS1071bd Whirlpool washing machine. I have had problems when you press start it sounds like water is going into the machine then it starts flashing 'door open' error. I have checked...

Hi from retired Englishman in SW France,

Sorry but 'door open' error message means that it thinks the door IS open even when it isn't! There is likely to be a problem with either the door solenoid/lock or the 'door closed' sensor. Both require a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C
0helpful
1answer

LG wf-t6517tc, stop after fill water, dE code error

Strange that it should fill as that means door error. You would think it would not fill if it thinks there is a door error. Have you tried switching off, unplug leaving for a few mins? If you can empty it check the door seal,/ latch it may require a new door switch.
Also check that the pump filter is not partially obstructed, be careful water will come out when you check. I read that in another post, I also read that it means drain error but that is at odds with what is written here: read this below it should help and there are pictures
http://lgknowledgebase.com/kb/index.php?View=entry&EntryID=799

regards
0helpful
1answer

Machine stopped mid cycle and green light flashing under green start button

Many modern washing machines display error codes if they detect a fault, but not all washing machines display a readable error code, some indicate an error by flashing, or lighting some of the lights.

Hotpoint, Indesit, Zanussi error codes

Hotpoint, Indesit washing machines and Zanussi washing machines are some common appliances that display coded error codes. On their more expensive models, they display readable error codes but basic models (without digital displays) use flashing lights to convey the error fault code.

If your washing machine malfunctions and you can see some of the lights flashing, or one or more option lights have lit up, then make a note of which lights are flashing and which option lights are lit. NOTE: the error code list engineers have only shows the option lights by number and not by name. Therefore you need to report the lights as LED 1 and 3, or 2 and 4 etc. and NOT "delay timer" and "extra rinse". Count the lights from the left (or from the top if in a column) and report as "led 1 and 3" etc.

No Option lights?

With basic washing machines that have no option indicator lights, count the number of flashes. For example, the door locked indicator may flash 7 times, pause, and flash another 7 times in a constant cycle which would indicate error code 7.

This information is vital, and needs mentioning when reporting a fault.

2helpful
1answer

Model GW611 the first and second last led flashes. fills up and wont go into wash cycle

If by first led you mean green to the left & amber to the right then that is fault code (130) & i think it is (Rotor Position Sensor) If you meant first to the right that would be red & green, code 65.no that doesn't sound right.its 130 & im sure thats rotor sensor.
1helpful
3answers
0helpful
2answers

The start button won't turn green when power turned on.

if the machine needs toner you will be able to change paper size & reduction but the machine will not come to ready[green ready light lit]. so if the machine keeps running after you turn it on it needs toner. if you leave it on for lets say 15 min. does it give you an add toner light or an error code?
Not finding what you are looking for?

1,111 views

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Brad Brown

Level 3 Expert

19127 Answers

john h

Level 3 Expert

27898 Answers

mark warfield
mark warfield

Level 3 Expert

453 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...