Question about Samsung RGSF5330DT Gas Kitchen Range

1 Answer

Oven Temp Display

The display is blank and it has 120VAC to the display plugs. I assume the module has gone bad. Before I pay $150 do you have anything I could check?

Posted by Nick Fowler on

  • Nick Fowler Jan 26, 2007

    The board was blank for three days and now has fixed itself and has been working correctly for three days. I put the board purchase on hold to see how long it continues to work. Strange situation.



1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 10 Answers

If the oven doesnt work and the display is blank then you would have to get a control board for the unit.

Posted on Jan 24, 2007


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Samsung smh2117s. The display does not light up, however the touch pads all work. How do you get the light back?

SAMSUNG SMH2117s is a Microwave oven.. :-D
you're in the wrong section. This is for mobile phones.

But, may be the display is gone if you cannot see any lights(Assuming the Microwave oven itself has a LCD to display temp, time..etc.. I don't actually know the model. But many Ovens are digital.). In this case, do not dismantle,crack open it. This is far beyond a rookie operation.

Jun 07, 2017 | Samsung Cell Phones

2 Answers

My whirlpool double oven accubake GBD307PDS09 display went blank then beeped. The oven does not turn on but when I tried to turn it on just to test it, it beeped once and then three short beeps. I have...

Hello Diana,
Their are a few things that should be checked. I know its going to be tough to check on a built in double wall oven but one thing that needs to be checked is if their is 240 volts ac entering the oven(i know the breaker is ok) but the connection at the back of the oven can burn,then the proper voltage wont enter the oven.
Another thing is a high limit thermostat thats inside of the control panel,need to checkif it has blown.
Last thing i can think to check is if 120 volts is at the clock, if not 120vac that explains the blank display

Aug 20, 2011 | Whirlpool GBD307PDS Electric Double Oven

1 Answer

The electric panel on the front of the oven is not lit up. Checked the breakers and power is good. Can't operate at all as unable to turn on etc.

First, flip the breaker off for one minute, then on again. If the controller has crashed because of a power glitch or cosmic ray event, this will reset it. (Download user manual if necessary.) You will need to set up your options again, and custom cooking programs may be lost as well. I assume you have already verified that the oven is still properly plugged in.

In that doesn't work, a fuse inside the oven or something in the controller module has gone out. First, assume it's a display failure, and try to operate it "blind." Does that do anything? If it does, you have a good starting point for an electronic technician to work on the controller, and you know it's not a fuse. If operating blind doesn't do anything, a good electronic technician should still be able to trace its power supply circuits and identify the problem component (most of the parts cost less than $2 and the rest are usually impossible to obtain anyway). An appliance tech will change the controller module, ask for $150-$300 for the part and another big chunk of change for labor. If you are mechanically inclined, you may able to buy the controller online yourself and change it for considerably less- just be sure to switch off the breaker before you start!

Nov 18, 2010 | Miele DG 4080 Stainless Steel Electric...

1 Answer

Kenmore GAS Range, model 970-334422, display/oven control went blank, light still works in oven.

it is very likely that the display may have gone bad. but before you buy a new one does it have any thing on it at all

Aug 19, 2010 | Kenmore 78812 / 78814 / 78819 Gas Kitchen...

1 Answer

Jenn-Air JJW8527 oven display has been progressively getting dimmer and now it will not display any settings. The oven still responds to controls and bakes, but it is difficult to know if you set it right...

The problem is likely bad capacitors on the clock module. I had the same problem on a similar oven and fixed it by replacing the capacitors on the clock module. Find someone who is good with electronics to help you. The parts will be a few dollars at most. Give them a tip too. See this link for more info:

Jul 06, 2009 | Jenn-Air JJW8527C Expressions Collection...

1 Answer

Jenn-Air Electric range clock display

The problem is likely bad capacitors on the clock module. I had the same problem on a similar oven and fixed it by replacing the capacitors on the clock module. Find someone who is good with electronics to help you. The parts will be a few dollars at most. See this link for more info:

Oct 06, 2008 | Jenn-Air JGR8850 Gas Kitchen Range

1 Answer

Clock/oven/temp screen for a Jenn-Air electronic range #SVE87600

I believe Jenn Air will pay a portion or electronic parts replacement on their ranges less than 5 years old.
You might try unplugging the stove for 1 hour and this is supposed to reset the stove to factory settings

Sep 06, 2008 | Kitchen Ranges

Not finding what you are looking for?
Samsung RGSF5330DT Gas Kitchen Range Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Kitchen Ranges Experts


Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6234 Answers

Brad Brown

Level 3 Expert

18591 Answers

Are you a Samsung Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides