Question about Hayward 1 12 Hp Super Swimming Pool Pump Sp2610x15

Open Question

How to connect on 220 volts al the wires on hayward super pump

Posted by Anonymous on

Ad

5 Related Answers

john224

John Prohaska

  • 1378 Answers

SOURCE: wire Hayward Super Pump for 115

If you look closely, you should see a small arrow on the black plastic piece on the terminal block(jumper). That arrow lines up with either the 115 or 230 mark on the white terminal board. Make sure it is aligned with the 115.

Then put you two line wires on. It does not matter which wire goes to line 1 and line 2, just be sure you DO NOT put them both on the same terminal. A plastic divider usually seperates the two line connection terminals.

Posted on Jun 13, 2009

Ad
MNfisherman

Nate Stansfield

  • 11896 Answers

SOURCE: my hayward super pump has a wiring diagram but it

Is one screw silver and one brass? Or are they both silver or both brass?

Posted on Aug 20, 2009

Ad

poolyoda

  • 128 Answers

SOURCE: Need wiring diagram for Hayward dual Super 2 speed

You need 4 wires to wire the 2 speed pump. You will also need a 2 speed time clock.. Tightwatt or intermatic. The wiring diagram is on the motor.

Posted on Aug 30, 2009

john224

John Prohaska

  • 1378 Answers

SOURCE: I am installing a Hayward Pool pump max flo II at

Either one. Neutral to the other post. Be sure to set the voltage change device to 115V to match your incoming line voltage.

Posted on Sep 15, 2009

Testimonial: "That's outstanding info for anyone installing a pool pump. Tom Smith"

A Miller

  • 8404 Answers

SOURCE: I'm need assistance wiring my hayward 2 speed

You may have a faulty bearing ... causing the noise. The pump is actually water cooled. Do you have 2 inch line for your 2 HP pump? Small pipe makes the pump work harder. If your lines are smaller, you may want to consider a smaller pump.

the motors will run pretty warm.

Run your pump on high for best results.

If you are using a timer ... you will need a double pole switch to turn it off if it is setup for 220 VAC (which it should be, for most econimical operation)

Posted on May 25, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I burned up a 1 1/2 Super Pump. I see it was originally wired for 120 and am wondering if I should wire it for 230 with my new pump. What are the advantages/disadvantages of 230 vs 120v.


120 volt carries a higher amperage through the circuit, while 220 carries a lower amperage through the circuit. Safety and wiring sizes come into play here. 230 will always be better over 120 for the above reasons, and also for the fact that it is more cost effective on your electrical bill.

wire your circuit and your pump for 220volt if possible. Only use 120 volts if you have to do it and theres no other options.

Apr 13, 2011 | Hayward SUPERPUMP 2.0 HP, 115/230V

1 Answer

How to install hayward motor?


Just the motor? Three things you must consider: There are 4 bolts that fasten the motor to the pump housing. You need to determine 110 Volts or 220 volts - 220 will run the pump more efficiently. Bonding. Your motor must be bonded to all other metal parts of your pool system.

Aug 22, 2010 | Hayward 1 Hp 2 Speed Super Pump Inground...

1 Answer

Can you please tell me the correct wiring for a Hayward 120V pool pump (not 240V) Thank you


Follow diagram on the tag. typically low voltage and high voltage volt are diagramed on the tag. Most manufactures send pumps out already for 220. the A and B terminals are for pump wires. and the lines are for the power cord. follow the diagram and you can't go wrong;

The Pool Tech

Jul 10, 2010 | Hayward 1HP Super Pump II Inground Pool...

1 Answer

If you are replacing a 2 hp pump with a Hayward 2 hp super pump on a 220 line is L1 white and L2 black


Shouldn't be a white line on a 220 circuit but some people use them. Red and Black is the standard. If you are sure they supply 220 VAC, which I would verify, it doesn't matter which one goes to which terminal. 120 or 3 phase matters. If you have a multi meter, put the red lead on the black wire and the black lead on the white wire. If you read 220, good. If you read 120, it will make a difference.

Jun 26, 2010 | Hayward SUPERPUMP 2.0 HP, 115/230V

1 Answer

Looking for a diagram on a hayward pool pump electrical wiring model super 11


What specifically are you looking for (beside the fact you asked for a diagram)?

It should be setup for 220 Volts ... the only thing inside is a start cap.

Can you tell me more? I maintain 5 2 and 1 1.5 hp such pumps.

Oct 14, 2009 | Hayward Super Pump 1 1/2 - Hp for In...

1 Answer

I am installing a Hayward Pool pump max flo II at 120 volt. I have 2 connections L1 and L2. Which one does the black hot wire go to.


Either one. Neutral to the other post. Be sure to set the voltage change device to 115V to match your incoming line voltage.

Sep 15, 2009 | Hayward 3/4hp Super Pump Inground Pool...

Not finding what you are looking for?
Hayward 1 12 Hp Super Swimming Pool Pump Sp2610x15 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hayward Pool & Spa Experts

john h

Level 3 Expert

23438 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Paul Carew

Level 3 Expert

3524 Answers

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...