Question about Epson Stylus Color 3000 InkJet Printer

1 Answer

EPSON 3000 TURNS OFF WHILE PRINTING

When printing my Epson 3000 while turn off, sometimes turning back on immediatley, but interupts/wastes product. The on/off button remains in the same position and if I bang on it sometimes it will comee back on. Is it the hardware or software. Please help!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

This is certainly a hardware issue and only servicing would solve this issue. Sorry

Posted on Sep 10, 2007

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

Reset my Epson printer L382


Follow the steps given below to reset Epson L382 printer.
Step 1: Turn the printer off.
Step 2: Press and hold the reset button which is on the back of the printer using a paper clip or tip of a pen.
Step 3: Turn on the printer by holding the Power & reset button and continue to hold both the buttons.
Step 4: Wait for 5 seconds and a warning sheet will print. Release the reset button.
Step 5: After 5 seconds, another sheet will print which will show the IP address of the printer.

hold the reset button which is on the back of the printer using a paper clip or tip of a pen.

WHERE IS RESET BUTON? I CANT FIND IT.

Sep 08, 2018 | Epson Office Equipment & Supplies

1 Answer

Epson SX210wont


Disconnect the Universal Serial Bus (USB) cable from the back of the product, but leave the product turned on

Open the cover of the product and remove the print cartridges

Close the cover and wait for the Insert Ink Cartridges message to display

Disconnect the power cord from the back of the product and wait for one minute

Reconnect the power cord. If the product does not automatically turn on, press the Power button

Open the cover and reinsert the print cartridges

Close the cover. If prompted, print a calibration page. Hope It's resolve all Your Printer Problem,
Or Still having Problem Then follow Us ForEpson Printer Support

Apr 01, 2014 | Epson Stylus Office Equipment & Supplies

1 Answer

I need to reset the waste ink counter on my epson 2200 printer.


1. Turn off the printer power and unplug the power cord from the wall. Disconnect the computer interface cable at the back of the printer. 2. After one minute reattach the power plug to the wall, but don't reattach the computer cable. 3. Hold down the ROLL and the PAPER ADVANCE buttons simultaneously. 4. Turn the printer on. after 2 blinks, all the ink lights come on, then release the buttons being held down. 5. Press and hold the ROLL button for 10 seconds 6. Release the ROLL button and the printer will initialize, which resets the Waste Ink Pad Counter. 7. Once initialization is complete, turn the printer power off. 8. Reconnect the interface cable. 9. Turn the printer on and print a document.

Oct 20, 2010 | Epson Stylus 2200 InkJet Photo Printer

2 Answers

I have epson tx110 and all the lights keeps on flashing and says general error?


This error means that some mechanical parts of your printer is in trouble. This could be some of the causes:

1. The print head is stuck somewhere or is unable to move because of some blockage in the printer's bay.
2. If you are using a Continuous Ink System, then the tubes might have blocked the print heads from moving.

To resolve, turn OFF your printer. Remove such blockage then turn the printer back ON.

Regards,
JR

Oct 06, 2010 | Epson Stylus Multifunction Inkjet Printer/...

2 Answers

Epson R320 Service required message


Reset waste ink counter using SSC ver. 4.30. You can find at indoreset.blogspot.com. Don't forget to replace waste ink pad, washing or extend outlet pipe from head cleaning mechanic to outside of printer.

Jul 23, 2009 | Epson Stylus Photo R320 InkJet Printer

1 Answer

Green and orange lights flashing, saying service error 6000


read all first!
you didn't say how many blinking
and in what order so ...
First thing you need to do is print an EEPROM information page, step number 2 below.
Once you have an EEPROM print you can reset the waste ink counter, if needed, which is step number 4 below.
Service Mode: This printer has a service mode for service-related settings and for performing test prints. The operator panel buttons are used to enter the desired service mode.
Service Mode Operations
With the printer powered off, hold down the "Resume Button" and press the "Power Button".

While holding down the "Power Button", release the Resume Button" and press the "Resume Button" twice in succession. Now release the "Power Button".

The indicator will blink in green and remain lit in green.

Select one of the following service mode functions by pressing the “Resume Button” the specified number of times.

1 time = Service test print.
2 times = EEPROM information print.
3 times = EEPROM initialization
4 times = Waste ink counter resetting
5 times = Destination settings
6 times = Print head deep cleaning

Then press the “Power Button” one time to perform selected function.

If you press the "Power Button" two times it will take you out of service mode.

This information is listed above in this thread and many times in other Canon threads in this forum. I simplified Canons wording so I could remember the service mode functions easier.



PIXMA IP 3000 service error 5100

I got service error 5100 after a paper jam sometimes 5 times blinking orange. in my PIXMA IP 3000

to fix it
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

or: and Also;
Unplug unit, hold power and reset button down then plug it in while still holding both buttons down;
Then to step 3 above.

Feb 19, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

I have a canon pixma ip 3000 and i need to empty inktank can u help


Ther is no ink tank it is a counter pre set by canon who decided you can only print so many pages . it is artificial number.
reset your machine by the following should help
read all first
First thing you need to do is print an EEPROM information page, step number 2 below.
Once you have an EEPROM print you can reset the waste ink counter, if needed, which is step number 4 below.
Service Mode: This printer has a service mode for service-related settings and for performing test prints. The operator panel buttons are used to enter the desired service mode.
Service Mode Operations
With the printer powered off, hold down the "Resume Button" and press the "Power Button".

While holding down the "Power Button", release the Resume Button" and press the "Resume Button" twice in succession. Now release the "Power Button".

The indicator will blink in green and remain lit in green.

Select one of the following service mode functions by pressing the “Resume Button” the specified number of times.

1 time = Service test print.
2 times = EEPROM information print.
3 times = EEPROM initialization
4 times = Waste ink counter resetting
5 times = Destination settings
6 times = Print head deep cleaning

Then press the “Power Button” one time to perform selected function.

If you press the "Power Button" two times it will take you out of service mode.

This information is listed above in this thread and many times in other Canon threads in this forum. I simplified Canons wording so I could remember the service mode functions easier.


to fix also :
PIXMA IP 3000 service error 5100

I got service error 5100 after a paper jam sometimes 5 times blinking orange. in my PIXMA IP 3000

to fix it
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

or: and Also;
Unplug unit, hold power and reset button down
THEN plug it in while still holding both buttons down;
Then to step 3 above.

Feb 18, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

U2 main code 40 subcode on A-162 Printer


u2-40 is a code that this copier will show if the toner unit is a non oem product , you can rest simulation 16 in the service modes but the error many come back

clear, interupt , 0 , interupt , 16 clear all and print
many need to do this severl times

Feb 09, 2009 | Sharp Office Equipment & Supplies

2 Answers

Red & Green Lights keep flashing on Epson Stylus Photo1280


I had the same problem. You need to reset the waste ink counter:

1. Turn printer off, unplug power cord. Disconnect computor interface cable (back of the printer).
2. After one minute, reattach power cord, but not the computor interface cable.
3 Hold down the LOAD/EJECT and CLEANING buttons simultaneously (cleaning button has ink drop on it) .
4 Turn printer on. Release all buttons as soon as the paper out light flashes.
5 Quickly press the cleaning button, and hold for 10 sec while paper out light flashes.
6 Release the button and the printer will initialize.
7. Once the initialization is complete, turn the printer off.
8. Reconnect the interface cable.
9. Turn the printer on and try to print your document.

This process worked for me. Good luck!

Feb 01, 2009 | Epson Stylus Photo 1280 InkJet Printer

1 Answer

I have an Epson 2200 and the Light black ink light is on even thought I have a new cartridge in there. This is the second cartridge I've tried. Same thing. Any suggestions?


this means that your printer wast pad is full this is how you can reset your printer
  1. Turn off the printer power and unplug the power cord from the wall. Disconnect the computer interface cable at the back of the printer.
  2. After one minute reattach the power plug to the wall, but don’t reattach the computer cable.
  3. Hold down the ROLL and the PAPER ADVANCE buttons simultaneously.
  4. Turn the printer on. after 2 blinks, all the ink lights come on, then release the buttons being held down.
  5. Press and hold the ROLL button for 10 seconds.
  6. Release the ROLL button and the printer will initialize, which resets the Waste Ink Pad Counter.
  7. Once initialization is complete, turn the printer power off.
  8. Reconnect the interface cable.
  9. Turn the printer on and print a document.
  10. make sure you have got new wast pads in

Dec 04, 2008 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Epson Stylus Color 3000 InkJet Printer Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Inky Fingers
Inky Fingers

Level 3 Expert

705 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Alun Cox

Level 3 Expert

2679 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...