Re: Need Information on setting clock on Pioneer...
I just tried it after researching on other sites. Keep the ignition on and the power to the stereo off. Hold down the function button (on the lower left for the DEH-P47DH) for a few seconts and the arrows will let you adjust the time.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Okay, I'm assuming that you were sucessful in resetting your radio code.
I'm also assuming that you have a CD player (which may not be the case).
The flashing clock also functions as an error code indicator. It should say something, indicating what the error is. You can't set the clock until the error is resolved (a disc stuck in the CD player, for example, on no disc in the CD when it's been told to play).
The procedure is as follows (which you probably know): The audio system display usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II). It shows the operation mode of the radio, cassette player, or optional CD player/changer when you operate them, then goes back to the time display after five seconds. If an error occurs while operating the optional CD player or changer, the display will keep showing the error code and will not switch to the time display until the error is corrected.You can set the time only when the clock is displayed. To set the hours, press the H (Preset 4) button while pressing the CLOCK (SCAN/RPT) button. Press and hold the H button until the hour advances to the desired time.
To set the minutes, press the M (Preset 5) button while pressing the CLOCK (SCAN/RPT) button. Press and hold the M button until the minutes numbers advance to the desired time.
If you don't have a CD player, or no error is showing in the clock read-out, leave a comment so I can investigate further.
Hope this helps you.
You can try the following steps
Setting the clock 1 Press and hold SEL (select) for more than 2 seconds. “DEMO,” “CLOCK H,” “CLOCK M,” “DIMMER,” or “AMP GAIN” appears on the display. 2 Set the hour. 1 Select “CLOCK H” (hour) if not shown on the display. 2 Adjust the hour. 1 2 3 Set the minute. 1 Select “CLOCK M” (minute). 2 Adjust the minute. 1 2 4 Finish the setting. To check the current clock time or change the display mode Press DISP (display) repeatedly. Each time you press the button, the display changes as follows: • During tuner operation: • During CD operation: • During power off: The power turns on and the clock time is shown for 5 seconds, then the power turns off.
Setting the time
This is used to set the time on the unit’s clock
1 Press SOURCE and hold until the unit turns
2 Press AUDIO and hold until TIME (12:00)
appears in the display.
3 Select the portion of the time display you
wish to set with left\right.
Pressing left\right will select a portion of the clock
As you select portions of the clock display the
portion selected will blink.
4 Select the correct time with up\down.
Pressing up will increase the selected hour or
minute. Pressing down will decrease the selected
hour or minute.
• To cancel time settings, press BAND.
• You can also cancel time settings by holding
down AUDIO until the unit turns off.
Can get the PDF of the manual on line and pg 8 tells you how. Basically you hit the title button till time is displayed. (Title button is on the right of the screen) Then hold the title button down until time blinks (hour blinks) to the dial and turn the dial and the hour will adjust. Then press the mode button (the one just below the dial) Then turn the dial again to fix the minutes.
Hi, i have a manual in front of me. To set the clock
press DSPL button for 2sec
press volume +/- button to set the hour
press SEL, then the minute indication flashes
press the +/- button to set the minute
For most Pioneer single CD players, you can set the clock using the following steps:
1.Press and hold the SOURCE button until the unit shuts off.
2.Press and hold SOURCE again until the clock appears. With some models you will press and hold the FUNCTION or AUDIO button instead of the SOURCE button.
3.Press the left or right arrow to select the segment of time you wish to adjust.
4.Press the up or down arrows to increase or decrease the numbers in the blinking segment.
5.Once the clock is set correctly, press the SOURCE button to exit.