Question about Razor MX500 Dirt Rocket

1 Answer

How to put the wiring back together

It was working and a plug broke and it had four wires and then another plug broke and im trying to put the wires back together

Posted by jessie on


1 Answer

Kelly A. Shaner

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

This is a wiring diagram for the Mx500 razor. hope this helps!

Posted on Sep 15, 2012


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006. Wires disconnected from underhood fuse box panel. How do I determine which wire connects where?

Not quite sure what you mean, did you break a wire harness loom that keeps all the wires bundled together or did you break an actual plug connector?
If you broke a loom clip them use black electrical tape to wrap the wires back together. If you broke a plug, go to the dealer and buy the new plug or harness. the new plug will have mew wires already attached and all you'll have to do is match color, cut, splice, solder, heat shrink and plug back in.
If you have another problem for some reason or another that I haven't hit on then I'd suggest going to your local parts stor or dealership and buy the repair manual for your car, turn to the electricl schematic section and follow your color codes from there..
Good Luck

Jul 13, 2015 | Nissan Quest Cars & Trucks

1 Answer

My girlfriend had a friend start work on her 99 Buick LeSabre. He tore the intake cover off, all the fuel rail, the spark plug wires off, broke a plug in the block, pulled the alternator off, as well as a...

Hi Jason,here's a link on your fuel rail,Here's a link on your spark plugs,Why was he working on it to begin with?Here's how to put your alternator back on.Need more help,let me know.

Aug 17, 2013 | 2000 Buick LeSabre

1 Answer

How to bypass a lid switch on 26002010

You first un plug machine. Front panel has screws in the four corners. Trace lid switch to the back of panel. Cut the two wires and strip wire and put together , use **** connectors and put all back together. As you now, when washer is on high spin, make sure no kids open lids, as you just bypassed safety feature.

Jun 06, 2011 | Kenmore 20172 Top Load Washer

1 Answer

I have a 1998 ford escort zx2 four cylinder an i just put a stater on it an while i was putting it on i accidentally broke a red and yellow wire on the harness an i dont know were it suppose to go it split...

all wires in a cars harness are color coded so now carefully cut the tape back until you find the leads and then repair them. you will need to use wire connectors don't just twist them together. by the way those are the solenoid wires.

Oct 01, 2010 | Ford Escort Cars & Trucks

1 Answer

Hello, Im trying to rewiremy transmission on a 92 GMC 3500 vandura box van. My don chewed the wiring that plugs into the transmission The plug has 11 wires coming out of it but some of them that he didnt...

Hello tnvolsfan32,

Use the FREE drawing available on the
BBB Industries site to trace out your wiring...
BBB Industries Premium Alternators Starters Power Steering Products

First put the wires together that
back to the drawing and find out what
disconnected or swallowed.

Generally wires DON'T CHANGE COLORS
in a wiring harness run... So you definitely
need to look for a LOGICAL EXPLANATION.

Registration is required... these are real
wiring documents...

Each time you return from a WIRING page
make sure you have not
defaulted back into TSBs...
(technical service bulletins)... While usually
quite useful... they don't begin to address any
WIRE-EATING-DOG problems...

If you get confused comment me back...
I can recommend some great tools to help
SPLICE everything back together

Tone Tracer being PRIMARY
Extech TG20 Wire Tracer and Tone Generator Amazon com

Helpful hint: wire must be ISOLATED to trace correctly
(pulled fuse or chewed through works).

Hope this helps

Carnac the Magnificent

Sep 23, 2017 | GMC Cars & Trucks

1 Answer

Samsung synmaster 204t "green board"

Most likely, this is an orientation sensor.
The monitor supports a "MagicRotation" feature, which automatically switches between portrait and landscape mode when the screen is rotated. I think the part you damaged is a mechanical orientation sensor required for this feature. This would explain why it had a loose metal ball inside (shorts two contacts together, depending on the orientation).
So I guess, you should still be able to use the monitor without the sensor. Uninstall the "MagicRotation" utility (if you had it installed at all) and set the orientation manually.

Mar 28, 2010 | Samsung SyncMaster 204T Monitor

1 Answer

Need help with epson pos

its not the relephone plug the 24 v wires sound about right i believe the telephone plug would be for credit/debit card sales via a built in modem and magnetic card reader hook up the wires first by stripping them back and electrical taping them together put drawer in and plug it in should work if not switch wires try again once it works either solder or use a **** conector or wire nut and tape to ensure it doesnt ground out

May 21, 2009 | Epson Computers & Internet

Not finding what you are looking for?
Razor MX500 Dirt Rocket Logo

Related Topics:

3,063 people viewed this question

Ask a Question

Usually answered in minutes!

Top Razor Cycling Experts

Andrew Taylor
Andrew Taylor

Level 3 Expert

32319 Answers

ray gallant

Level 3 Expert

67911 Answers


Level 3 Expert

35290 Answers

Are you a Razor Cycling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides