Question about Jensen VM9511TS AM/FM/CD/DVD/SD Player/7" LCD Car Video Player

2 Answers

My TFT display screen only shows white. (white, not blue)

I have installed my unit, checked all connections, accessed the brake override per the hidden menu code, and connected a rear display. The rear display shows everything perfectly. The unit screen shows only white. Anyone got a suggestion or is it a defective unit?

Posted by Nick Nixon on

  • Wilson Ondeko
    Wilson Ondeko Oct 07, 2019

    Hi try check the fiber connector loading the video signal, if it is intact probably the screen on board transistors could have failed due to overheating and hence requiring new replacement.

×

Ad

2 Answers

Anonymous

Unit was defective, I returned it for another and it works perfect.

Posted on Sep 13, 2007

Ad

Mitch

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 752 Answers

Sounds to be defective. All white is not normal under any conditions.

Posted on Sep 11, 2007

  • Willie McNair
    Willie McNair Oct 06, 2019

    Ribbon is just loose

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

I have a set Motorola Canopy 2400BH but i forgot ip address and username and password, how can i access it for using.

You need to user an Override Plug, which can be fabricated this way:

To fabricate an override plug: 1. Install an RJ-11 6-pin connector onto a 6-inch length of CAT 5 cable. 2. Pin out all 6-pins. 3. Short (solder together) Pins 4 and 6 on the other end. Do not connect any other wires to anything. The result should be as follows: Pin 1 ? white / orange ? Pin 1 Pin 2 ? white / green ? Pin 2 Pin 3 ? white / blue ? Pin 3 Pin 4 ? green ? Pin 6 Pin 5 ? blue ? Pin 5
Regaining access to the module To use the override plug 1. Insert the override plug into the RJ-11 GPS sync port of the AP. 2. Apply power to the module through the Ethernet cable. RESULT: The module reboots with the default IP address of 169.254.1.1, password fields blank, and all other configuration values as previously set. 3. Set passwords as desired. 4. Change configuration values if desired. 5. Save the settings. 6. Remove the override plug. 7. Power cycle the module.
You can view more details at:
http://www.canopy-wireless-solutions.com/AppicationNotes/APManualIss5.pdf
0helpful
2answers

Hunter 44860 touch screen temperature override

"Hunter" says it all. Throw it out and buy a honeywell, robertshaw, or a white-rodgers. Hunter stats are notorious in the business as being problematic.
4helpful
2answers

What does the green/white wire connect to on my jensen vm9312hd? Says it is reverse +

Rear View Camera Input: The VM9313 features a composite video input and a green/white wire lead attached to the harness for connection of a rear view camera. If a rear-view video camera is connected, the unit is on, and the TFT monitor is retracted inside the unit, the TFT monitor automatically moves into the viewing position and Camera modes is selected upon shifting into Reverse gear. When shifting into Drive gear, the TFT monitor is retracted back inside the unit. If the monitor is already in a viewing position and in display mode, the monitor automatically switches to Camera mode upon shifting into Reverse. When the reverse driving stops, the monitor returns to its original input display mode. You can choose for the monitor to display a Mirror mode image or a Normal mode image from the rear-view camera.
2helpful
1answer

Jensen player

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.
1helpful
3answers

Jensen in dash dvd monitors

I got this from another forum so don't thank me, thank psychedelic feta. I'm just passing it on, WORKS LIKE A CHARM!

FWD:
The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. if you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.
0helpful
1answer

DVD player

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.
0helpful
1answer

Is there a way to keep the screen out?

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.
0helpful
1answer

Jensen dvd not showing

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.
0helpful
1answer

Brake bypass

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.
Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

617 views

Ask a Question

Usually answered in minutes!

Top Jensen Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5023 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

The Knight
The Knight

Level 3 Expert

76703 Answers

Are you a Jensen Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...