Whirlpool GS460 Gas Kitchen Range Logo

Question about Whirlpool GS460 Gas Kitchen Range

1 Answer

Error F1E2 Whirlpool Super Cap Gas Range 465, oven crazy!

Initially began with no "beep" when turning on, then set oven to 350 and I know it was WAY higher as it burned up what I put in. Gas range working fine, just the oven. Gets heat, just TOO much! help! Didn't even get the error message display for days.... then it appeared. Thank you!

Posted by kimvillani on

Ad

1 Answer

Ron Coons

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Whirlpool Master
  • 2,651 Answers




F1 E2

1. Verify failure if not displayed, using CANCEL/OFF key. Press key for 5 seconds until last
error code is displayed.
2. Disconnect power longer than 30 seconds.
3. Re-apply power and observe for longer than 1 minute.
4. If failure remains, disconnect power, replace control.



Posted on Nov 23, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Whirlpool super capacity 465

You may have several things going on f1 e4 is a control board issue with the touch panel plug in into the control board disconnect and reconnect if this problem presist will need a control board and touch pad for the oven not staying lit there is a new oven igniter kit 8190618 unfortunately no good diagnostics for this problem good luck
Feb 18, 2014 • Ovens
0helpful
1answer

WHIRLPOOL Sup Cap 465 oven turns on for 3 sec, then shuts off

The flame sensor is dirty or bad.

When the unit does not sense flame after ignition, the gas valve shuts down the system.

They can become corroded or dirty, but usually just need to be replaced.

Contact whirlpool for warranty info. If the unit is under warranty, they should send you the parts for free. If not, they can direct you in how to order the part.

http://www.whirlpool.com/custserv/email_form.jsp
0helpful
1answer

My oven heats up, but then does not maintain the temp.

If it has a pilot then I would say the thermal couple is bad. If it has a glow type ignitor then the ignitor is bad.
6helpful
2answers

Whirlpool Accubake Super Capacity 465 gas range. Oven won't light

Some gas ranges may take 10 or so minutes to light.
Other than that you may have a defective glow bar ignitor.
If it glows and does not light the reistance in the ignitior has failed.
Feb 25, 2009 • Ovens
4helpful
5answers

Whirlpool Accubake Super Capacity 465 gas range. Oven won't light

i dont know want is wrong with it when i turn the oven on it keeps saying e2 and f3 i dont know what that mean please help me one on .... :(
1helpful
2answers

Whirlpool super capacity 465 gas range model# sf377pegq5

I have the same problem intermittently on my Super Cap 465. After reading the following quote from another site, "There have been cases where radio waves, electronic signals and sometimes something as strange as dimmers in lights have caused some weird problems with some computer panels in stoves like these", I tried turning off lights that might be on the same circuit and wouldn't you know it, the oven igniter circuit worked.
4helpful
3answers

Whirlpool Super Capacity 465

I have the same problem intermittently on my Super Cap 465. After reading the following quote from another site, "There have been cases where radio waves, electronic signals and sometimes something as strange as dimmers in lights have caused some weird problems with some computer panels in stoves like these", I tries turning off lights that might be on the same circuit and wouldn't you know it, the oven igniter circuit worked.
0helpful
1answer

Whirlpool 465 oven temp

Go to Calibration mode and adjust the temperature up by 10, 20 or 30 degree. This is in each manual.
32helpful
6answers

Whirlpool Accubake oven super capacity series 465

Press and hold the Broil button for 5 seconds. You will see the c change to f. THen change the temp to what you need.
Not finding what you are looking for?

501 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6557 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Paul Carew

Level 3 Expert

3736 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...