Question about Zenith D52WLCD 52" Rear Projection HDTV-Ready Television

Yellow Tint on Screen

I purchased a used non working Zenith D52WLCD recently. I completely dissassembled it, thoroughly and carfully!) removed all the dust and crud, and replaced the bulb and ballast. It worked! All is well except for two things: 1. There is a yellow tint to the lower third of the screen. 2. The "replace bulb" red light is still on even though the new bulb I put in work fine. Any suggestions?

1 Answer

Bill Heronemus

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.
Expert
308 Answers

I would guess that the light engine is not aligned right with the chassis. You will probably have to get into the menus and reset the bulb timer setting to get rid of the replace bulb light. A common problem with these sets is a clogged lint screen causing the set to overheat and shut off after a period of time.

Posted on Jan 01, 2007

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

WHAT IS THE PART NUMBER FOR THE OPTICS/LIGHT ENGINE FOR D52WLCD??

It comes as a complete chassis assembly only and I have included a link to a website for purchase. The only issue is the cost is almost equal to purchasing a replacement TV. Please take a few moments to rate my response. Thank you..

http://www.partstore.com/Part/LG+Electronics+Incorporated/LG+Electronics%2fZenith/D52WLCD/LG+Electronics+Incorporated/LG+Electronics%2fZenith/3141VSNA61C/New.aspx

Nov 17, 2009 | Zenith D52WLCD 52" Rear Projection...

1 Answer

My zenith D52WLCD has a blue haze going diagonally

This a Normal Intensive Use Defects, this a Screen Burnout. Sorry

Oct 31, 2009 | Zenith Televison & Video

1 Answer

I have a Zenith d52wlcd and the screen is dark or excessively blue.

Go to the Zenith repair site. This has been resolved in a lawsuit. Zenith will fix it free of charge through 7/1/2010. The shop just picked my up to replace the light engine free of charge. Call 1-800-228-1757, have your model number and serial number, and where you purchased it. Here's the neat thing-the question I asked is "have they fixed the problem with the light engine, or is it going to keep going bad?" If happens again (blue lines/spots) before 7/1/2010, they'll replace the TV with a new and different TV of equal value!

Jun 27, 2009 | Zenith D52WLCD 52" Rear Projection...

1 Answer

The screen has a yellow tint

I had a friend who had this problem and the repair shop replaced some liquid or gel that the lens shine through and afterwards the picture looked like new again.

Oct 22, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

How to reset lamp hours

try holding the enter button on the tv and the mute button on the remote. a reset screen will pop up and then just press the center direction button twice.

Sep 04, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Zenith project color tv advanced video imagining

I will tell you but it will cost you. Choose one of my assistance plans at a nominal fee. Sincerely, Michael

Aug 31, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

ZENITH D52WLCD

I just found the solution on another model of Zenith TV. Hold the enter button down on the TV and the MUTE button on the remote. In approx. 5-7 seconds a screen will pop up asking if you want to reset the lamp timer. Hit the bullseye button in the middle of the arrows and it will reset. Worked perfectly.

Apr 15, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer