Question about Gadzoox Networks Slingshot 4218 Networking Switch

2 Answers

Slingshot Admin password removal/reset and User's manual

Hi I have a friend who bought a second hand slingshot 4218, but he cant manage the switch because it is password protected. Is there a jumper inside or a battery i can disconnect to reset the password to fabric results? Finally, there are no manuals from gadzoox on the net anymore, so if somebody knows where to find, please let me know any hint much appreciated, regards Rodrigo

Posted by Rodrigo Sosa on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

It's not a regular home use switch or router. For pro or business router, switch, and this type fibre Channel switch, there is no certain way to reset or recover the password, the only way is find the facotry service guide, quite un-fortune, this company has been acquired by Broadcom, no support anymore. Usually, admin/password, root/admin, or admin/secure maght be a combination, just give a try.

Posted on Nov 29, 2008

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 31 Answers

Most of the switches/hubs have a reset button in front or on back. If there is no reset button, then more then likely you will need a crossover cable, you can probaly get one at compusa or radio shack. With the power off to the Switch, and all cables disconnected, plug one end of the cross over cable into WAN port 1, and plug the other end into LAN port 1. Power on, and wait for the front lights to cycle through. After about 3 minutes, power off, power on, wait 2 minutes, power off, plug in all normal cables and power on. This should take it back to factory default, and you shoudl be able to log into it from the web browser of a PC plugged into it. Most default ip addresses are either 192.168.0.1 or 192.168.1.1

Posted on Jun 06, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Mikuni carb diagram

HI Keith. As far as l know the bore size varied over the years, 1987 - first models - were 36mm, l've got a set.
Google Slingshot carbs & Suzuki GSXR 750 Slingshot carbs, there's a wealth of info on how to identify & also do a complete strip down

Regards Clive






live




/&
Nov 25, 2013 • Motorcycles
0helpful
1answer
0helpful
1answer

Optiview

try the user as admin and the password as admin..
If my memory serves, there is also a master reset switch..
Look for a small hole in the rear of the case, power the unit off, press and hold a small pin into the hole to hold the switch in and then switch the power back on..
I know ya need three hands to do this...
If no hole is present, check inside the case on the board for the reset switch..
0helpful
1answer

Where can I get a replacement Roboraptor remote

hi did you find a affordable replacement? I am asking as I also need one..please email [email protected] .co.nz...cheers
Jul 11, 2010 • Toys
0helpful
1answer

Hi I own a 1988 Gixer 750 slingshot.

check your fiber clutch plates and tranmisson forks.
16helpful
1answer

Wants to reset 3824 3com switch via console

You forget the password for the "admin" user account and can no longer perform important management operations. solution.gif Use the password recovery method outlined below to define a new password for the "admin" user account:
  1. Access the Command Line Interface from the console port and enter the user name "recover" and password "recover" to place the Switch in password recovery mode. The Switch remains in password recovery mode for a maximum of 30 seconds, before it returns to the CLI login prompt.

    note.gif You must use the console port to recover the passsword. If you attempt the recovery method using the network, the password will be rejected.

  2. Perform a hard reset on the Switch whilst it is in password recovery mode by switching it off, waiting a few seconds, and switching it on again.

    note.gif You cannot use a soft reset operation to reset the password of the "admin" user account. This will end the password recovery procedure and return you to the CLI login prompt.

  3. When the Switch has rebooted following the hard reset enter a new password for the "admin" user account.
Not finding what you are looking for?

Open Questions:

See all Gadzoox Networks Slingshot 4218 Networking Switch Questions

Gadzoox Networks Slingshot 4218 Networking Switch Logo

539 views

Ask a Question

Usually answered in minutes!

Top Gadzoox Networks Computers & Internet Experts

Ekse

Level 3 Expert

13435 Answers

Brad Brown

Level 3 Expert

18825 Answers

Cindy Wells

Level 3 Expert

6370 Answers

Are you a Gadzoox Networks Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...